If you are the owner of a summer cottage, cottage or country house and want to have high-quality digital TV with the maximum number of channels and a minimum monthly fee, then the optimal solution would be to connect Tricolor TV FullHD satellite television. Below we will tell you how to correctly make the cabling for connecting satellite TV Tricolor TV in a country house, cottage or in the country where should a satellite dish for satellite television "Tricolor TV" be installed, which cable should be used, which sockets should be installed.
In a cottage, a country house, a summer residence, just like in an apartment, you can connect any number of TVs to Tricolor TV. Connecting one TV set to Tricolor TV in a cottage or country house, dacha, as a rule, does not cause difficulties. But connect Tricolor TV "on several TVs- the task is more difficult. The main task is the correct construction of the distribution television network and the selection of the necessary equipment and cables. That in the future, after connecting Tricolor TV, will allow avoiding many problems during operation.
How to connect "Tricolor TV" to several TVs using satellite receivers
Suppose you want to connect Tricolor TV to 3, 4, 5, 6 or more TVs in a cottage, dacha or country house. The first step begins with the selection and installation of the coaxial cable. The cable must be marked "SAT", i.e. must pass a satellite signal with a frequency of up to 2400 MHz. And do not trust the "experts" who will assure you that cheap cable also passes the satellite signal and everything works well. This is true, but only half, over time, the cable ages, as a result of which the frequency characteristics of the cable change, which worsens the passage of the satellite signal, and after a few years the signal will either completely disappear, or the picture on the TV will constantly “fall asleep”. The distribution television network (to connect "Tricolor TV") is built as follows: from the installation site of each TV, one cable is laid to the installation site of the satellite signal distribution device (it can be a multiswitch or an active splitter). The switchgear is an active equipment, therefore, at the place of its installation, it is necessary to provide a power outlet with a power supply of 220 V. Further from the place of installation of the switchgear, 2 cables are laid to the place of installation of the satellite dish. If 1 cable is laid to the antenna and it is not possible to lay another 1 cable, then it is possible to use polarizing diplexer... It allows transmission of 2 polarizations from an antenna to a multiswitch via one cable (there are restrictions on the use of a polarization diplesker along the length of the cable and its attenuation coefficient). The antenna is installed only on the south side. In the immediate vicinity of the antenna installation site, on the south side, there should be no tall trees and buildings. A television outlet is installed near each TV set; it (like the cable) must be marked "SAT".
All other equipment for connecting Tricolor TV is selected by our specialists. They choose a place for installing the antenna, install the antenna, tune it to the Eutelsat 36A / 36B satellite at 36 ° East, end the cable with F-connectors, connect the cables, install and configure the satellite signal distribution device, measure the signal level and quality in television sockets ... Finally, they install and connect satellite receivers and TVs.
How to connect a combined system; Tricolor TV + digital terrestrial channels.
If you have a large number of TVs in your house and not all TVs are used equally intensively, we recommend installing a combination system. In which the most commonly used TVs, which require the maximum number of channels (including in high definition format - Full HD), are connected to Tricolor TV satellite television, and TVs on which 30 digital channels are sufficient are connected only to digital free channels ... Digital channels are broadcast from the Ostankino TVC as part of 3 multiplexes - RTRS 1(Russia 1, Match TV, Russia 24, NTV, 1 channel, Russia K, Karusel, 5 channel, TVC, OTR), RTRS 2(Muz TV, TNT, Mir, Zvezda, Friday, TV-3, Domashny, STS, Spas, Ren TV) and RTRS 3(Match! Arena, [Match! Game, Match! Fighter, My Planet, Science 2.0], [Russian Novel, Russian Bestseller, Russian Detective, History, Cartoon], [Sundress, Country], [Amusement Park, IQ HD, 24 Doc, 24 Techno], [Mother and Child, NSTV], [Trust, Euronews], [Music of the First, House of Cinema, Time, Telecafe],, Our football, Life news). This system will allow you to save on the annual subscription fee, because there is no subscription fee for multiplexes RTRS 1, RTRS 2 and RTRS 3. To implement the system, satellite and digital terrestrial antennas are installed. From the satellite dish, you need to run two cables to the switchgear and one cable from the digital terrestrial antenna. All cables are connected to one device. The digital terrestrial signal must be amplified before connecting to a distribution device. For this, an amplifier or, more preferably, a mini headend is installed.
As a result, at each branch of the switchgear there is both a satellite signal "Tricolor TV" and a digital terrestrial signal, which is fed to each TV through the distribution network. For TV viewing of Tricolor TV channels, a Tricolor TV receiver or CAM module is installed. On the remaining TVs, digital terrestrial channels are watched.
How to connect Tricolor TV without using satellite receivers.
If in your house, cottage, TVs are fixed to the wall and there is no place for installing the Tricolor TV receiver, or you want to control the viewing of Tricolor TV satellite television with only one TV remote control, then we suggest installing a Cam-module (conditional access module DRE- Crypt MPEG-4) or headend.
To connect "Tricolor TV" using a Cam-module, it is necessary that the TV supports the DVB-S / S2 MPEG-4 format and has a CI slot ( Common Interface). In this case, the distribution network is built in the same way as for connecting Tricolor TV on satellite receivers. A special TV interface, through a TV network, connects to a satellite dish. The cam-module is installed in the CI-slot of the TV, the TV broadcasting settings are registered in the TV menu.
And on November 15, 2015, Tricolor TV began broadcasting an Ultra HD package in 4K ultra-high definition. Two ultra-high definition TV channels TRICOLOR ULTRA HD and INSIGHT UHD are broadcast with a resolution of 3840x2160 pixels and a transmission rate of 50 frames per second. The first viewers of the Ultra HD Tricolor TV package will be the subscribers of the "United" package with a CAM module. Broadcasting is carried out without additional subscription fees, and this is round-the-clock broadcasting of documentaries and feature films, entertainment and sports programs in 4K format.
Tricolor TV connection has been completed. Satellite TV viewing is controlled by a remote control from the TV.
Connecting Tricolor TV using a television satellite headend is a more complicated and expensive task. In this case, the signal from the satellite dish is fed to the headend, where it is converted into a digital cable DVB-C format. And from the head station through the distribution television network, the signal is fed to the antenna input of the TV. Setting up the TV is carried out by the usual channel search through the menu.
How to connect Tricolor TV to 4 TVs based on GS E501 / C591 system.
In mid-2014, General Satellite has developed and released on the market a set of Tricolor TV equipment for 2 TVs - GS E501 / C591. The cost of such a system is not much higher than the usual set for 1 TV. And the option of connecting 4 TVs using 2 GS E501 / C591 systems is the most budgetary. However, the connection diagram of the "Tricolor TV" GS E501 / C591 system is somewhat different from the classic one. This must be taken into account when laying cables. To install the Tricolor TV GS E501 / C591 system, the satellite dish is installed as for conventional equipment. The converter must be used QWAD - with 4 independent outputs. 2 coaxial SAT cables are laid from the converter to each GS E501 receiver (server). And the GS C591 receivers (client) are connected to the GS E501 receiver via UTP cable cat. 5e (twisted pair). If there is a computer network in the house - SCS, then the UTP cable cat. 5e does not need to be laid as the signal can be transmitted over the SCS home network. A schematic diagram of the Tricolor TV system for 4 TVs based on the GS E501 / C591 set is shown on figure.
The variety of audio - video connections is sometimes frightening with its abundance and the user is unable to choose the correct connection to the Tricolor set-top box on his own. A fair question arises; how to connect the Tricolor receiver to the TV yourself?
The most expensive set of equipment for receiving a digital signal from a satellite is a receiver. And in order to immediately eliminate misunderstandings, when buying a tricolor set-top box, it is advisable to check the list of recommended equipment on the official website and choose a receiver that is suitable for you.
What are the connections and how to choose the right signal source
In addition to the main power cord, through which the satellite TV receiver is turned on, the following audio-video outputs can be found on the rear panel:
- analog RF;
- composite audio - video AV output;
- S-Video format;
- SCART format;
- component output Y Pb Pr;
- HDMI (High Definition Multimedia Interface).
Let's go through each of them in order and determine the appropriate connection type for your digital satellite receiver.
Analog RF is an outdated video and audio signal transmission format that was previously used as an antenna input for receiving analog TV and radio broadcasts.
Composite audio - video AV output is the most common type of connection that can be found practically on any TV or satellite box. In the common people, this type of compound is called the March flower - "tulips".
You can use colored cables if you still have an old CRT TV receiver. In order to independently connect, it is enough to connect the corresponding color ends of the cable to the jacks on the set-top box and the TV.
The S-Video format is the most interesting connector, which is very similar to connecting a keyboard or computer mouse to a system unit. It can be found on more expensive TVs and receivers. It resembles a round socket with several contacts inside.
The SCART format is a common type of connection between a receiver and a TV, a European standard through which video and audio signals pass at the same time. The picture quality when connected via SCART is comparable to the image obtained when connected via the component video output. It is a thick cable at the ends of which there are connectors with 21 pins. In order to independently dock the TV and the receiver, it is enough to connect the corresponding ends to the jacks on the set-top box and the TV receiver.
Component Y Pb Pr is a type of cable connection that is capable of transmitting high definition signals up to 1080i. The cord is a set of multi-colored cables that transmit the signal corresponding to its color.
- Green is for HDTV transmission. Brightness Y
- Red HDTV Cr \ Pr Chroma
- Blue HDTV Cb \ Pb Chroma
- And also additional, red and white for audio channels.
In order to independently connect the tricolor receiver via a component cable, you must carefully read the instructions and not confuse the cable. Most TVs and receivers are equipped with this type of connection. This is due to the fact that the channel can transmit a picture in high definition without significant loss of quality. If your TV allows you to make a connection in this way, you should not give up this choice. The output picture will be significantly different in quality from the previous connection methods.
HDMI (High Definition Multimedia Interface) is a modern format for transferring data between a tricolor receiver and your TV. The advantage of HDMI connection is bypassing additional conversions in the video signal transmission process. That is, the digital signal enters the TV in the form in which the telecom operator broadcasts and does not undergo any changes.
For pairing your receiver to a TV, the best option is an HDMI connection, if of course the receiver and TV receiver have one. Since satellite TV channels are moving to a new broadcasting standard. And the tricolor TV company is no exception, it is slowly giving up broadcasting its TV channels in MPEG 2 and MPEG 4 formats and is switching to broadcasting HD television. Therefore, it is advisable to use a connection that can transmit the broadcast picture to TV with the highest quality.
Wiring diagrams of the tricolor receiver to the TV
Connecting a digital receiver to a TV can only be carried out using certain connecting cables. The circuit is very simple; you need to take a suitable cable and connect it to the corresponding output of the set-top box, the other end to the same socket to the TV. If you have difficulty in determining the required outputs, you can use the diagram shown in the figure.
The scheme for self-pairing of two TVs is slightly different from the first task, but these differences are not significant. So, in this case we need a second, longer cable for the second TV. If in the first case you use a tulip connection, then another connection must be selected for the second TV receiver, for example, SCART or HDMI.
It should be noted that the second TV will show the same channel as the first, since the TV signal from the tricolor set-top box is turned on and controlled. In order for the second TV to show a picture independent of the first, you need to purchase a second receiver. An additional receiver turns on and works through the same antenna as the first one, only a separate output on the converter is used. In this case, both receivers will work independently of each other.
An important point for self-connecting the set-top box to the TV is to use the minimum number of wires. It is also not worth making a connection with deliberately long cables, since a long cable loses part of the signal.
Tricolor TV is a fairly popular satellite TV provider in Russia. Many of us use or are going to use the services of this company, which means that the topic of connecting and using the equipment of a set of receivers is relevant. In this article, we would like to talk about connecting and configuring the GS E501 / GS C591 receivers from Tricolor TV.
So, the company provides its users with the opportunity to view satellite TV channels, while providing display of various channels on two different television receivers.
That is, in fact, a set of receivers GS E501 / GS C591 is able to provide independent broadcasting for two TVs. It is important to note that the main receiver is the GS E501, it is he who receives and decodes the RF signal. In fact, there are two receivers installed in it. And the second receiver GS C591, in fact, is not a receiver either. This is just a set-top box that receives a digital signal via a wire connection and works with it. The connection via Wi-fi is not carried out as this method is not able to provide transmission for display in HD quality.
At the same time, it must be said that despite such features, the receiver and the set-top box are able to provide full viewing of satellite channels independently, when each of the devices can work with its TV, in another room and from its own remote control.
The GS E501 receiver ("server") is designed to receive a signal from a satellite dish converter and broadcast TV and radio channels to a client receiver through a local network.
The GS C591 receiver ("client") is designed to play TV and radio channels ("content") received from the server via the local network.
Depending on the conditions (the location of the receivers in the premises and the distance between them, the presence of a ready-made local network and free ports of network equipment), one or another scheme of network connection of the receivers can be used - direct cable connection, or connection to network equipment (router).
Direct cable connection of Tricolor receivers to each other
In this wiring diagram, the receivers are directly connected with an Ethernet cable (patch cord), as shown in Figure 1:
1) Connect a network cable to the Ethernet port on the back of the server.
2) Connect the other end of the patch cord to the Ethernet port on the back of the client.
3) Power on the server and client.
Connecting to network equipment of Tricolor TV receivers
In this scheme, the client and server are not connected to each other directly, but are connected to the network equipment, as in Figure 2. This connection scheme requires two patch cords and two free ports of network equipment:
1) Connect the patch cord to the Ethernet port on the back of the server.
2) Connect the other end of the patch cord to an available port on your network equipment.
3) Connect the second patch cord to the Ethernet port on the back of the client.
4) Connect the other end of the second patch cord to an available port on your network equipment.
5) Power on the server and client. It is also necessary that the power to the network equipment is turned on.
Setting up the receiver - server GS E501 Tricolor TV
1) After connecting the receivers to the local network, set the server network parameters in the “Settings Wizard” application at the “Network Settings” step (or in the “Settings” application, in the “Network” section), see Figure 3.
Figure 3
2) Using the buttons on the remote control "← / →", "/ ↓", move the focus to "Ethernet 0" and, by pressing the "OK" button, select the method of obtaining the IP address for the server:
"DHCP" as shown in Figure 4 or
Link local, as shown in Figure 5.
DHCP is not applicable for direct connection scheme. For this scheme of connecting receivers, you must select the Link local method. For connection to network equipment, depending on the presence of a DHCP server in the network, both DHCP and Link local can be selected. The settings for the method for obtaining IP addresses (Link local or DHCP) must be the same for the client and server.
Figure 4
Figure 5
3) Using the remote control buttons "←", "Exit" return to the window of the list of network interfaces
Figure 6
4) If the server has received an IP address, the screen should look like Figure 6. This means that the server is connected to the network and you can proceed to configuring the client.
Figure 7
5) If the screen looks like Figure 7, it means that there is a problem with the server connection. A general list of possible problems when connecting the server and actions for their elimination are shown in Table 1.
Configuring the receiver - client GS C591 Tricolor TV
1) After configuring the server, set the client's network parameters in the “Settings Wizard” application at the “Network Settings” step (or in the “Settings” application in the “Network” section), see Figure 8.
Figure 8
2) Using the buttons on the remote control "← / →", "/ ↓", move the focus to "Ethernet 0" and, by pressing the "OK" button, select the method of obtaining an IP address for the client:
"DHCP" as shown in Figure 9 or
Link local, as shown in Figure 11
DHCP is not applicable for the direct connection described in section 3. For this receiver connection scheme, select Link local. For connection to the network equipment described in section 4, depending on the presence of a DHCP server in the network, both DHCP and Link local can be selected.
The settings for obtaining IP addresses (Link local or DHCP) must be the same for the client and server.
3) After the client and the server receive IP addresses, the client must find a server in the local network: in the field under the heading "Select a server" will be displayed
server information as shown in Figure 10.
“90000101010518917315799” in the example in the figures is the identifier (serial number) of your GS E501 receiver.
4) To connect to the server, use the "/ ↓" buttons on the remote control to move the focus to the line with the server identifier and press the "OK" button. After a successful connection to the server, the message "Established connection to the receiver-server 90000101010518917315799" will be displayed, as shown in Figure 11.
Figure 9
Figure 10
Figure 11
5) If the screen still looks like in Figures 8 and 9 (the client did not receive an IP address, an empty list of servers), as well as in Fig. 12 (the client's Ethernet 0 network interface is not connected to the local network), this means that there is a problem with the client and / or server connection. A general list of client connection problems and corrective actions are shown in Table 2.
Figure 12
6) The configuration of the client's network parameters is completed after eliminating the possible problems described above and receiving the message about a successful connection to the server, shown in Figure 11.
7) The next steps are to complete the client setup, including determining the operator and region, searching for channels and watching the content on the TV connected to the client.
The length of the patch cord should not exceed 100 meters. Patch cords are not included in the delivery set of receivers - receivers GS C591 and GS E501 and are purchased or manufactured by the user himself. It is very important that the network cable is properly and properly crimped. The cable is crimped in a standard network manner, ie, "direct" connection, when the pinout of the twisted pair for both ends of the cable must be the same.
Satellite television "Tricolor TV" has come to many homes in our country. Their kits are in a well-deserved and constant demand among the population due to the high quality of the signal, low cost and ease of purchase via the Internet. After you purchase a satellite dish and a receiver, you can order the service of a full range of works on the installation of a set of television "Tricolor TV" from a specialized company. In this article you will learn how to independently install, connect and fully configure the Tricolor TV satellite system.
Assembling the kit
Even a person who is completely unfamiliar with technology can independently assemble the purchased kit. If you decide to install and configure your dish and receiver yourself, we advise you to study the instructions and remember the names of the components of the satellite dish. You should also understand exactly where and how the Tricolor TV receiver is connected.
Prepare a TV cable with plugs. The first step is to place the converter in the holder.
Pay attention to the connector, it should be directed downward so that rain does not flow into it.
The mounting sleeve must be securely fastened to the converter working area. Before installing the antenna, we advise you to check and tighten all the bolts again. In order to correctly tune the head and find the exact direction to the Tricolor TV satellite, this will have to be done more than once during the installation process.
Antenna mounting
To obtain a high-quality image on the TV screen, coming through the receiver output, it is necessary to fine-tune the antenna to the Tricolor TV satellite and the absence of visible interference on a straight line mentally drawn between them.
Before proceeding with the installation, carefully read the documents of the equipment set and find the name of your set there: "Center" or "Siberia".
The saucer must face due south, and must also be attached exclusively to an outer wall or mast. In no case can it be installed between high-rise buildings or trees covering an imaginary axis drawn between the plate and the satellite.
If it was decided to independently install the receiving device on the outer wall of the house, then the bracket should be fixed with reliable anchors. If this rule is not followed, strong winds can tear off the mounts and the antenna can cause a lot of trouble. The place for installation should be chosen from a simple calculation: as close as possible to the place where the receiver is installed.
Even when using a double-braided cable with a thick copper core, this distance is limited to one hundred meters. If it is impossible to install the kit so close, we recommend purchasing and setting up an additional amplifier. The process of acquiring it is not complicated, it is usually available in any store selling television equipment.
After the purchase, the antenna is first assembled and installed on the already fixed bracket. We clean the television cable from the top layer of insulation at both ends by one and a half centimeters. In the direction from the end to the middle, carefully wrap the shielded braid and screw the F-connector onto the freed part. We leave the main copper core protruding two millimeters beyond the connector, bite off the rest with pliers. Now you need to connect the receiver with a cable that goes to the antenna converter.
We connect the receiver
There are two ways to connect the Tricolor TV receiver to the TV yourself:
- high-frequency connection with an antenna cable;
- low-frequency connection of the receiver with an ordinary cable with "bells" or a "scart" connector.
For HF connection: plug the cable into the antenna socket of the TV and connect it to the receiver's RF Out. Then we connect the receiver with a cord to an electrical outlet and turn on the power switch. The screen should display "BOOT" and the channel number. Then we start the automatic channel search in the television receiver and look for a channel with the inscription "No signal", indicating to us that the receiver is connected correctly.
With LF connection: the receiver is connected with a cable with "tulips" or "Scart". We turn on the receiver to the network and wait for the word “BOOT” to appear on the screen, and then the numbers of the channel number. On the control panel of the television receiver, the video mode is set by pressing the "A / V" key. If we see the inscription "No signal", then the receiver is connected correctly.
Next, you need to check the presence of a strong signal coming from the satellite to the receiver. We try to display any random channel on the TV. The screen will display the channel number, the program broadcast from the satellite to the dish and the time. Since the antenna is not tuned, the TV screen will have a blue color over the entire background.
We are looking for the inscription "i" on the remote control of the receiver and turn on this button. Two scales "Signal strength" and "Signal quality" should appear on the screen, according to which the settings should be set, and then we will independently adjust the satellite dish.
Customization
The last important stage of the work required to obtain a high-quality image on the TV is the correct setting of the satellite dish and the Tricolor TV receiver. This action can be performed independently, keeping the antenna direction strictly to the south. It is advisable to carry out further actions to establish signal reception from the antenna together with family members or any assistant.
Put it in front of the TV and wait for commands from it about the result on the screen, independently and gradually turning the satellite dish up and down an inch, right and left.
The presence of a neighboring antenna "Tricolor TV" makes it much easier to set up. Just copy its direction and slope, achieving the most complete filling of the fields of both scales on the screen.
You need to start adjusting the signal from the vertical position of the plate mirror, gradually moving it in the horizontal plane. We look at the screen: if both scales are full, it means that we have caught a good signal. Soon, a high-quality image appears on the television receiver. If only one scale is full, the signal does not come from the Tricolor TV satellite, you need to look further. Little by little, independently turning the antenna mirror, first horizontally, then vertically, we adjust the maximum filling of the scales and the highest quality image on the TV screen.
registration
To register the receiver you will need:
- Tricolor TV card number;
- receiver serial number;
- the code indicated on the card;
- owner's passport;
- kit installation address.
The easiest way is to register your receiver number through the Tricolor TV website. After filling out a special registration form, your agreement number will be shown in the window and the card will be activated. The agreement can be downloaded from the website, printed, signed and sent to the address indicated on the website by regular mail to the company for signature.
You can register the installation by calling the company phone numbers listed on the site. It will take a little time, and the result will be the same, the contract will be sent to you by mail. The most important thing is that along with the purchase of your favorite TV shows, you get a guarantee for the entire set of equipment! We wish you that self-installation and tuning of the satellite dish and receiver "Tricolor TV" was successful and good mood as a result of watching interesting television programs!
TricolorTV is a company offering high quality television broadcasts. However, configuring the hardware to work properly can be difficult. The market for digital technologies is very large, and each manufacturer brings something different in both the receiver models and the TVs themselves. For some, the setup is automatic, while others require a more "personal" approach. LG TVs belong to the second group.
Why LG setup is different
About a year ago, many companies changed their broadcasting conditions - channel delimitation was introduced, which now called for sorting by lists. This affected users in such a way that the list of offered TricolorTV channels simply did not appear in the system, or did not appear in order / incomplete. LG TVs were particularly susceptible to this bug, whose software was unable to maintain the new order.
Difficulties arose mainly in those cases when users tried to search for channels using the "Quick Search" option. Algorithms for decoding signals in this case, LG TVs were perceived incorrectly, for which the company has repeatedly apologized. Almost all product lines of the company for 2014-2018 were “affected”, and some of them still demonstrate this bug.
LG is actively developing new software that would support the formation of such lists that TricolorTV uses. It is tentatively scheduled to launch in July 2018. However, this does not mean at all that TricolorTV subscribers who have LG TVs at home should refrain from watching TV, since there is a way to get around the problem on their own - and it lies in a slightly different sequence of settings.
In addition, most LG TVs were equipped with a CAM module, which replaces a standard receiver - the connection and setup are somewhat different from the usual algorithm.
How to set up channels
Important! All of the following works on webOS TVs.
Installation of equipment should be carried out in accordance with the instructions of TricolorTV - mounting the antenna and dish, laying the cables. The company offers its customers a complete set of necessary devices to correctly "dock" with the satellite and pick up the signal.
One of the main stages is the installation of the CI + Cam-module. In this case, the TV must remain off. It should be turned on after correct installation. In this case, the screen should display information about the equipment - about the card and the module itself.
Important! In some cases, at this stage, error No. 17 may occur, which indicates that the equipment was connected incorrectly, or the subscriber forgot to register with TricolorTV with the card data.
After all these preparations, the channels are set up like this (manually):
- You need to go to the menu, where you should find the item "Advanced settings".
- Select "Channels".
- Select "Search for channels and settings".
- You should choose the "Autosearch" option, despite the fact that you configure everything manually. Here you can enter unique settings for the Tricolor.
- Search mode should be set to "Satellite". If not, select it from the list.
- Choosing a satellite TV operator is also an important option. For Tricolor today you need to click on "Other operators".
- Exit autosearch - click on the cross, or press EXIT on the remote control. If you have 3 or 3.5 version of the LG axis and the Magic remote control, press the Back / Exit button while holding.
After that, you can start manual channel search.
- Re-enter the "Channel Search and Settings" through the advanced options menu.
- Press Manual Search, and make sure the Receive Mode is set to Satellite. If not, change it to this mode.
- Open the "Transponder" settings item and select ANY one from the list, avoiding the number 12226 / L / 27500.
- Then press "Transponder" again.
- Now select option 12226 / L / 27500, and check if the Add button appears on the side.
- Turn on "Search network" - click on this item and change the value to "On."
- Click the Add option you found earlier. Wait for the end of the search and press EXIT.
Important! In some versions of the software, instead of “Add”, “Update” will appear.
After that, the search for channels in the network will begin - during the search, the LG TV will check 22 transponders, and the result of such a check should be more than 300 channels, including radio and service arrays.
The list of channels will be formed in a special way due to the fact that the new software has not yet been released for TricolorTV. It will contain:
- Present digital and satellite services and radio channels;
- the order of the channels is messed up.
However, the list editor will be available, and you can easily select and mark those that the TV will have to skip in the future. The Skip function will help you hide them from the general list for easier navigation.
