Purpose of buttons:
Power on / off button for the selected device (POWER).
Remote setup button (SET).
Numeric buttons for direct channel selection (0 ... 9).
Play button (PLAY).
Stop button (STOP).
Pause button (PAUSE).
Record button (REC).
Rewind button.
Fast forward button.
Mute button (MUTE).
- button for selecting a device for control (TV, DVD, SAT, AUX).
Volume buttons (Vol- / Vol +).
Channel switching buttons.
Beginning of work:
Carefully, observing the polarity, insert the two batteries into the special compartment. Alkaline batteries are recommended.
Remember to change batteries at least once a year!
Configure the remote to work with the required devices. There are several ways to do this.
After saving the code, turn on your device and check the operation of all buttons on the universal remote control. If some of the buttons don't work as expected, try different code.
Entering the code manually:
Find the brand of your device in the list of brands in the table. Each brand of device has one or more four-digit codes. Press and hold the desired SET button, then press a device select button such as TV. When the indicator light comes on, release both buttons. The indicator stays on continuously. Enter your four-digit device code. As each digit is entered, the indicator lamp blinks and after entering the fourth digit will go out, and the code will be stored in the remote control memory. If the code you entered is incorrect, the lamp will blink twice and will continue to burn, unless you enter the correct code.
Manual code search:
If you do not know the manufacturer of your device or cannot find its code, you can select the code manually. To do this, first press and hold the "SET" button, at the same time press the button of the equipment you have chosen, for example "TV". When the indicator turns solid, release the buttons. Then press the SET button once again, the indicator will start blinking. Point the remote at the TV screen and press the POWER button. Each time you press this button, the remote sends a power-off signal, iterating through the codes in ascending order. When the signal is being sent, the lamp blinks at an increased frequency. When the correct code is found, your TV turns off. Press the button of the selected equipment "TV", the indicator lamp will go out, and the code will be stored in the memory of the remote control.
Automatic code search:
Turn on the device of your choice, for example, a TV, and point the remote control at it. Press the desired device selection button once, for example, "TV". Press and hold the SET button and the POWER button. After three seconds, when the indicator light comes on, release both buttons. The keypad will begin to send a power off signal, iterating through the codes in sequence in ascending order every two seconds. The lamp blinks while the signal is being sent. When the TV turns off, immediately press any button (except the SET button) to stop auto search. The indicator lamp will go out and the device code will be stored in the remote control memory.
At the end of the cycle, the indicator lamp on the remote control will go out, and the search mode will turn off. The search cycle can take up to 30 minutes. Every time when You start the search, it starts with the last stored code. If you do not have time to stop the automatic iteration of the code in time, it is not necessary to repeat the entire cycle again. Find out the current programmed device code, subtract a few units from it, enter the resulting value manually and then use the manual code search procedure. For example, you automatically start searching for your TV. The TV turned off, but you stopped the search with a slight delay, therefore the following code is stored in the device's memory, for example "1015". Program code "1000" manually. Then start the manual search procedure. If the required code is "1012", then after the twelfth press of the button "POWER ”, the TV turns off.
How can I find out the currently programmed device code?
Press the button of the selected device on the remote control once, for example, "TV".
The first digit of the code can be recognized as follows. Press and hold the "SET" button, simultaneously press the "1" button. Release both buttons. If the first digit of the code is 1, the indicator will blink once. The absence of the indicator signal means that the code digit is "0".
Second digit. Press and hold the "SET" button, simultaneously press the "2" button. Release both buttons. If the second digit of the code is "5", the indicator will blink five times. The absence of the indicator signal means that the code digit is "0".
Third digit. Press and hold the "SET" button, simultaneously press the "3" button. Release both buttons. If the first digit of the code is "7", the indicator will blink seven times. The absence of the indicator signal means that the code digit is "0".
Fourth digit. Press and hold the "SET" button, simultaneously press the "4" button. Release both buttons. If the first digit of the code is "3", the indicator will blink three times. The absence of the indicator signal means that the code digit is "0". After saving the code, turn on your device and check the operation of all buttons on the universal remote control.
For some brands of TVs, the "POWER ”has only the function to turn off the TV. To turn the TV back on, you must press any number button.
If your TV does not support certain features, such as the “MUTE "(mute), button"MUTE ”on the remote control will not function.
Code distribution table:
TV - 0000 ... 0268, 0700 ... 0746, 1000 ... 1037.
DVD - 0269 ... 0370, 0750 ... 0754, 0524 ... 0690, 3000 ... 3018.
SAT - 0371 ... 0523, 0800 ... 0884, 2000 ... 2024.
AUX, CD, DVD - 0524 ... 0690, 3000 ... 3018.
Specifications:
Working distance - at least 8 meters.
The transmission angle is at least 30 degrees.
Setting methods - manual or automatic search in the code base.
Dimensions (HxWxD) - 195x80x30 mm.
Net weight - 210 g
Five devices for simultaneous control.
Number of buttons 32.
Batteries AAAx2 pcs.
If you lose your TV remote control, you don't have to worry about it. There are always universal remotes on sale that, after a fairly simple procedure, can easily replace the original model. The process of connecting to the TV will take no more than 10-15 seconds. It is only important to know how to set up a universal remote control.
Device device
The design of the universal remote control is no different from the original models. Both types of devices have buttons for selecting channels, adjusting the sound, setting the timer and others.
Typically, both devices run on the same AA or AAA batteries. If you use one remote control for a large number of devices, then the batteries will have to be changed more often than in a conventional model.
Some features of the internal device may determine which devices can be controlled and how to set up the universal remote control. Gal LM p001, for example, has the ability to quickly connect to TV and SAT. Some other models are not equipped with this function.
Comparison of the original remote control with the universal
There is no external difference between the two types of control devices. They differ only in the set of functions.
The first and main difference is that universal remotes can be connected to a large number of devices and devices. You can use them at the same time. For example, using one universal remote control, you can turn on a TV, air conditioner, stereo system and any other electrical unit that allows control from a distance. Also, the remote control will allow you to control home theater functions, satellite dish and cable TV.
In addition, the cost of the universal remote control is lower than that of the original model, and the service life is generally longer.
For owners of old TV models, such a universal device will be a salvation in case the original controller is lost. The original remote controls for the models of previous years are simply not produced.
Are they really versatile
Any remote control can be used with different models of TVs, players and air conditioners. There are, of course, exceptions. For example, what if you can't set up the universal remote? How can you check if it fits a given device model? First you need to see the list of compatible models in the instructions for the remote control itself. If there are no instructions regarding this, and the connection cannot be established, the problem may be both in the remote control and in the TV.
The versatility of remote controls is determined by the fact that, unlike original devices, which can be configured to work with only one device, they can simultaneously work with different devices from different manufacturers. Moreover, they do not have to be reconfigured every time.
How to set up a universal remote
To establish a connection between your TV or other device and the universal remote control, follow these steps:
- Turn on the remote control and point it towards the device.
- Simultaneously press the OK or SET button (depending on the model of the remote control) and hold it for 3-5 seconds.
- Enter the code for your device model.
- Then press the TV button to confirm the connection.
If for some reason the remote control does not connect to the TV, you need to do these steps again. An incorrect device code may have been entered.
There is another way to set up the Huayu universal remote control. To connect such a device, you can use autosearch:
- Turn on the device to be configured.
- Press the SET button and then POWER.
- Release the buttons at the same time.
- Press the POWER button again and release.
- Check if the volume indication appears on the screen.
- Press the SET button twice in a row.
Not all universal remote control models support the auto search function. It is also possible that the auto search function is not supported by the TV itself. Therefore, for some cases there is only one way to set up the LM P001 universal remote control - manual.
Some brands have a quick search function. To connect in this way, you need to perform the following sequence of actions:
- Turn on the device you want to connect to.
- Press and hold the TV button for a while.
- Release the button when the power indicator is on.
- Press and hold the MUTE button.
- When the connection is made, release the button.
- It is easy to check the operation of the remote control - just change the channel or adjust the sound.
If none of the methods came up and the code specified in the instructions did not work, you can use the last method - sequential iteration of the code manually.
How to determine the TV code
Each model of the device has its own universal code that allows you to connect a remote control to it. It comes in three, four and five characters.
For example, to find out how to set up a universal remote control for Samsung, you need to look at the code information in the instructions for your TV or air conditioner.
It is important to remember that you need to enter the code of the connected device, and not the universal remote control.
Smartphones with universal remote function
Some newer brands of phones allow them to be used as a universal remote control. As a rule, they can only be connected to TVs with SMART TV function.
To set up a universal remote control on a smartphone, you need to download a special application and follow the installation instructions that will light up on the screen. With the help of the program, it will be possible to interact not only with the TV, but also with other devices that allow the remote control function.
This useful feature is available for a limited number of smartphone and TV models. To use your phone as a remote control, both devices must have Wi-Fi, infrared, or Bluetooth connectivity.
INSTRUCTIONS
BY CONFIGURATION
UNIVERSAL
USER MANUAL
UNIVERSAL REMOTE CONTROL GAL
Model LM-LE008
Universal infrared remote control
able to simultaneously control eight devices,
such as televisions, LCD and plasma panels, projectors and projection televisions, DVD players and recorders, home theaters, video recorders, satellite, cable, terrestrial digital television receivers, various audio devices, etc. It contains a large database of codes for various devices, and also has a learning function.
Learn function refers to the procedure by which the remote learns infrared signals from other remote controls. When device codes are not included in the built-in database, they can be read from the original remote control.
Before starting work, please read the contents of this manual.
PURPOSE OF BUTTONS
The delivery set includes a universal remote control and operating instructions.Buttons for setting up the remote control Device selection buttons POWER button to turn off the power MUTE button to mute the sound Numeric buttons External input switching button Button to return Menu call button Confirmation button Menu navigation buttons Channel switching buttons Volume buttons Playback buttons Stop, Back, Forward Record button SCAN MACRO channel scan button Macro function button Teletext buttons Colored contextual buttons LM-LE008 LM-LE008
OPPORTUNITIES
Large database of codes from various manufacturers Several setting modes: brand selection in the remote control menu, manual code entry, automatic code search, learning using the original remote control.Ability to control up to eight devices simultaneously Macro buttons Backlit LCD Clock
EQUIPMENT
Remember to change batteries at least once a yearInstructions
INSTALLING BATTERIES
Open the battery compartment cover by squeezing the latch. Carefully, observing the polarity, insert two AAA batteries into the battery compartment. If the remote has not been previously configured to work with your devices, you must complete the setup procedure. Programming data is saved in the memory of the device when there is no power supply. Therefore, if the remote control has already been configured, you only need to set the current time.- & nbsp– & nbsp–
CONSOLE SETUP
Before starting programming the remote control, turn on the device for which the setting will be made. If it is a VCR or DVD player, load the cassette or disc, respectively.- & nbsp– & nbsp–
SELECTING CODE BY MANUFACTURER
Press and hold the SET button, then press the device select button to operate, such as TV. Release both buttons. When the brand name appears on the display, use the cursor buttons to select the brand of your device, for example Philips. Check the function of the buttons, for example + CH- or + VOL-. If the buttons do not control the device or do not work correctly, select another code using the cursor buttons or.When the correct code is found, click the OK button to save the setting. After saving the code, SUCCESS appears briefly on the display.
- & nbsp– & nbsp–
SEARCH FOR CODE If your brand is not in the list or you cannot select the required code, it is recommended to use the search mode. In this mode, the remote control sends a control signal to the device, sequentially going through the codes.
Press and hold the SET button for 3 seconds. When CODE SETUP appears on the display, release the button. Then click the OK button. Use the cursor buttons or to select DEV SEARCH and press OK. Press the desired device selection button, for example TV. Then press the OK button to start the search. When your device responds to the remote control, press any button to stop searching. Check the function of the buttons. If they work correctly, click the OK button to save the code.
If necessary, repeat the search operation, which will start from the last memorized code.
- & nbsp– & nbsp–
LEARNING THE REMOTE
The learning function allows you to supplement the functional buttons of the universal remote control with the specific functions of some original remotes that are not available in the built-in base.- & nbsp– & nbsp–
Press the button to select the device for which you are teaching, for example, TV. Press and hold the SET button for 3 seconds. When CODE SETUP appears on the display, release the button. Use the cursor buttons or to select the LEARNING menu item and press the OK button. Use the cursor buttons or to select the LEARN KEY menu item, then press the OK button. When SELECT KEY appears on the display, press the button to be learned on the universal remote control, for example, MENU.
The remote control enters standby mode (WAITING on the display). Press and hold the corresponding button on your original remote control. When the command has been read, the display will show SUCCESS. If the display shows FAILED, it means that the command was not recognized. It is necessary to repeat the learning procedure. To exit to normal mode, press the device selection button, for example, TV.
If necessary, teach other buttons.
- & nbsp– & nbsp–
ERASING TRAINING DATA
Press the button to select the device for which you want to erase, for example, TV. Press and hold the SET button for 3 seconds. When CODE SETUP appears on the display, release the button. Use the cursor buttons or to select the LEARNING menu item and press the OK button. Use the cursor buttons or to select the DELETE KEY menu item, then press the OK button. When SELECT KEY appears on the display, press the button you want to clear. When SURE DELETE appears on the display, press OK to confirm. Repeat the operation for other buttons if necessary. To exit to normal mode, press the device selection button, for example, TV.ERASING ALL TRAINING DATA FOR SELECTED DEVICE
Press the button to select the device for which you want to erase, for example, TV. Press and hold the SET button for 3 seconds. When CODE SETUP appears on the display, release the button. Use the cursor buttons or to select the LEARNING menu item and press the OK button. Use the cursor buttons or to select the DELETE DEV menu item, then press the OK button. When SELECT DEV appears on the display, press the Select button of the device whose learning data you want to erase. When SURE DELETE appears on the display, press OK to confirm.
After successful erasure, SUCCESS appears on the display for one second. Press the EXIT button several times to exit to normal mode.
ERASING ALL TRAINING DATA
Press and hold the SET button for 3 seconds. When CODE SETUP appears on the display, release the button. Use the cursor buttons or to select the LEARNING menu item and press the OK button. Use the cursor buttons or to select DELETE ALL, then press the OK button. When SURE DELETE appears on the display, press OK to confirm. After successful erasure, SUCCESS appears on the display for one second. Press the EXIT button several times to exit to normal mode.
ADDITIONAL FUNCTIONS SET THE CLOCK
Press and hold the SET button for 3 seconds. When CODE SETUP appears on the display, release the button. Use the cursor buttons or to select the CONFIGURE menu item and press the OK button. Use the cursor buttons or to select TIME SETUP, then press the OK button. Use the cursor buttons or to select hour, minute, AM / PM. Use the numeric buttons to enter the time. Select AM / PM mode with the cursor keys or. After entering, press OK to confirm.
Press the EXIT button several times to exit to normal mode.
SETTING THE VOLUME CONTROL PRIORITY
This function allows you to define the main unit that controls the volume. For example, if an amplifier is selected as the main device, the + VOL- and MUTE buttons control the amplifier directly, regardless of the selected device.
Press and hold the SET button for 3 seconds. When CODE SETUP appears on the display, release the button. Use the cursor buttons or LM-LE008 to select the CONFIGURE menu item and press the OK button. Use the cursors or buttons to select VOL LOCK, then press the OK button. Use the device selection buttons to identify the main device, for example AUX (amplifier). Use the cursor buttons or to select ON to set the priority, then press the OK button to save. To disable the priority, select OFF. Press the EXIT button several times to exit to normal mode.
Only one device can be designated as master. And.
LCD CONTRAST ADJUSTMENT
Press and hold the SET button for 3 seconds. When CODE SETUP appears on the display, release the button. Use the cursor buttons or to select the CONFIGURE menu item and press the OK button. Use the cursor buttons or to select the CONTRAST menu item, then press the OK button. Set the contrast value with the cursor keys or, then press OK to confirm. Press the EXIT button several times to exit to normal mode.
ENABLE DISPLAY BACKLIGHT
Press and hold the SET button for 3 seconds. When CODE SETUP appears on the display, release the button. Use the cursor buttons or to select the CONFIGURE menu item and press the OK button. Use the cursor buttons or to select the LIGHT menu item, then press the OK button.
Use the cursor buttons or to select ON to turn on the backlight, then press the OK button to save. To disable the priority, select OFF. Press the EXIT button several times to exit to normal mode.
LOCKING SETTINGS CHANGE
Once the lock has been activated, the stored device code cannot be changed.
Press and hold the SET button for 3 seconds. When CODE SETUP appears on the display, release the button. Use the cursor buttons or to select the CONFIGURE menu item and press the OK button. Use the cursors or buttons to select DEV LOCK, then press the OK button. Press the button to select the device for which you want to block, for example, TV. Use the cursors or buttons to select ON to enable the lock, then press the OK button to save. To disable the blocking, select OFF. Press the EXIT button several times to exit to normal mode.
MACRO BUTTON
A macro button allows you to replace a sequence of several presses of different buttons with one operation. To send a macro command, hold down the MACRO button and press one of the preprogrammed buttons 1, 2 or 3. The maximum number of clicks in one macro command is 10.
For example, to play a DVD, the player and TV must be turned on. Next, the TV input must be switched to an external source.
Press and hold the SET button for 3 seconds. When CODE SETUP appears on the display, release the button. Use the cursor buttons or to select the MACRO menu item and press the OK button. Use the cursor buttons or to select the macro command number 1,2 or 3 and press the OK button. When the display reads SETUP, press OK to record the keystroke sequence.
Press DVD, Power, TV, POWER, AV in sequence. Then click OK to save the macro command. Press the EXIT button several times to exit to normal mode.
LM-LE008 To delete the macro command, press and hold the SET button for 3 seconds. When CODE SETUP appears on the display, release the button. Use the cursor buttons or to select the MACRO menu item and press the OK button. Use the cursor buttons or to select the macro command number 1,2 or 3 and press the OK button. When SETUP appears in the display, use the cursor keys or to select DELETE and press OK. Press the EXIT button several times to exit to normal mode.
SCANNING CHANNELS
This function allows you to sequentially change the channels of your TV or receiver. To do this, press and hold the SCAN button for 4 seconds.
When the display shows SCAN, release the button and point the remote at your device. The remote control will start sending switching commands, and the indicator lamp for the selected device will blink. Press any button to stop scanning.
SLEEP TIMERS
The timer function allows you to turn off a specified device either at a specified time (3 timers), or at a specified interval.Shutdown timer at a specified interval.
Press the button corresponding to the device you have selected, for example TV.
Press and hold the SET button for 3 seconds. When CODE SETUP appears on the display, release the button. Use the cursor buttons or to select TIMER SET and press the OK button. Use the cursor buttons or to select the SLP TIMER menu item, then press the OK button. When MINUTE 00 appears on the display, use the numeric buttons to set the desired time interval from 0 to 99 minutes. Press the OK button to confirm. OFF will appear on the display. Use the cursors or to set to ON (timer on) and press OK to confirm. Press the EXIT button several times to exit to normal mode.
When the set time comes, the universal remote will send a shutdown signal to the selected device. For example, at 12.23 PM the sleep timer is set to 23 minutes for TV. At 12.46 PM, the remote will turn off the TV.
Sleep timers at set times.
Press the button corresponding to the device you have selected, for example TV.
Press and hold the SET button for 3 seconds. When CODE SETUP appears on the display, release the button. Use the cursor buttons or to select TIMER SET and press the OK button. Use the cursor buttons or to select TIMER 1 (2 or 3), then press the OK button. Next, enter the time for the timer to run. Use the cursor buttons or to set the hour, minutes, AM / PM. Use the numeric buttons to enter the time. Select AM / PM mode with the cursor keys or. After entering, press OK to confirm. Use the cursors or to set to ON (timer on) and press OK to confirm. Press the EXIT button several times to exit to normal mode.
- & nbsp– & nbsp–
RETURN TO FACTORY PRESET (RESET)
Factory reset clears the device memory and personalization data. This may be necessary if the device is not working properly.Press and hold the SET button for 3 seconds. When CODE SETUP appears on the display, release the button. Use the cursor buttons or to select the CONFIGURE menu item and press the OK button. Use the cursor buttons or to select CLEAR ALL, then press the OK button. When the display shows SURE CLEAR, press OK to confirm. 9 LM-LE008
- & nbsp– & nbsp–
WARRANTY OBLIGATIONS
The warranty period is 6 months. from the date of sale.The warranty does not apply to products that have undergone mechanical damage.
Please contact your local dealer for all warranty issues.
The service life of the product is 3 years.
Made in China.
Manufacturer: Shenzhen New Solution Electronics Co., LTD No. 19, XiangShan Avenue, 3 Industrial District, Luo Tian Community, SongGang Street, Bao An District, Shenzhen, China NOTE.
Due to the constant improvement of design and technology, changes may be made to your device that are not noted in this manual and do not worsen its parameters. The manufacturer reserves the right to change specifications and software. In this regard, the implementation of some functions may differ from the description in this
LMRC13L, LMX11L, LMV302L, LMVB01L
BEGINNING OF WORK
Carefully, observing the polarity, install two AAA batteries in the special
Remember to change batteries at least once
Configure the remote to work with the required devices. To do this, you can
use several ways. After saving the code, enable your
device such as a TV, switch the remote control to TV control mode when
using the "TV" button and check the operation of all buttons on the universal
remote control. If any buttons do not work as expected then try
pick up another code. If this did not help or did not manage to find the code at all
device, you can teach the buttons of the universal remote control using the remote
original using the learning function.
ENTERING CODE MANUALLY
Find the brand of your device in the list of brands in the table. Each brand
the device corresponds to one or more four-digit codes.
Enter your four-digit device code. As each digit is entered, the indicator
the lamp blinks and after entering the fourth digit will go out, and the code will be stored in memory
remote control.
If the code you entered is incorrect, the lamp will blink twice and continue
light until you enter the correct code.
SEQUENTIAL iteration of the code
MANUALLY
Press and hold the desired device selection button, for example "TV". Across
3 seconds, when the indicator light comes on, release the button.
Turn on the TV and point the remote at it.
To select a code, use the "CH +" or "CH-" buttons. Every time when
You press a button, the remote sends a power-off signal, fingering
codes sequentially in ascending ("CH +") or descending ("CH-") order,
respectively. The lamp blinks while the signal is being sent.
When the correct code is found, your TV turns off. Click the "OK" button,
the indicator lamp will go out and the code will be stored in the remote control.
In some modifications of remote controls, brute force can
be performed using the "LEFT", "RIGHT" buttons
OR "VOL-", "VOL +", respectively
AUTOMATIC CODE SEARCH
Turn on the device of your choice, for example, a TV, and point it at it
remote controller.
Press and hold the desired device selection button, for example "TV". Across
3 seconds, when the indicator light comes on, release the button.
Press and release the “POWER” button on the remote control. The remote starts to send a signal
power off, going through the codes sequentially in ascending order
every two seconds. The lamp blinks while the signal is being sent.
When the TV turns off, press the "OK" button. The indicator lamp goes out,
and the device code will be saved in the remote control memory.
Every time you start an automatic search, it
starts with the last stored code.
At the end of the cycle, the indicator lamp goes out,
and the search mode is turned off. Cycle time
search can be up to 30min.
