Protective glass on "apple" gadgets is designed to protect devices from damage. A high-strength chemical composition is usually used to protect the display from chips and scratches. Some users neglect such protection, but in vain. Protective glass for iPhone 6 and other gadgets can significantly extend the life of your mobile device.
In this article, we will look at how to remove the protective glass from the iPhone 5 and devices of other versions. We will also pay attention to how to glue the protective glass on the iPhone. In addition, we will try to identify the advantages of this method of protecting the display over conventional film.
How to change and how to glue the glass - read the detailed instructions below.
If we compare the 2 main ways to protect the iPhone display screen - glass and film - most of the criteria will be in favor of the first.
The advantages of glass coating are:
- Increased strength with a small thickness of only 0.25 mm.
- The presence of an oleophobic coating that prevents the appearance of fingerprints on the display.
- Sometimes - the presence of a nano-coating, which gives an increased smoothness of the surface.
- Reliable fastening with silicone elements that do not allow the coating to move and prevent the formation of bumps and bubbles.
Flexible glasses to protect the display of mobile gadgets can also have hemmed edges. This means that the edges are rounded, so the coating is almost invisible. In addition, if the device is hit against something, the coating will not crumble. So if you are wondering what is the best protective glass - stop your choice on the element with hemmed edges.
Removing glass: precautions
Before you get started, you need to consider some rules. First, remember that the glass is quite strong on the display as it is very smooth. But the element is held not thanks to glue, but with the help of electrostatic forces. Thus, two perfectly flat surfaces are in close contact, and the glass cannot be removed simply by picking it with your finger. But it is also impossible to use a household object for this purpose, for example, a knife, since there is a risk of damaging the screen or case.
A silicone suction cup will not help in this situation either. If you stick this tool to a damaged coating, a void will form under it, and when pressed, it will slide off.
And if the mount is good, the suction cup will not go anywhere, but another problem will arise. The fact is that the sensor is attached to the body of the gadget using either glue or adhesive tape. The strength of these substances in terms of rupture is much lower than that of glass or a touchscreen. Therefore, strong pressure can lead to a complete breakdown of the display module and damage to its cables. You need to work carefully and carefully here.
How to remove protective glass from iPhone 5S, 4S
Even taking into account the fact that the period of operation of protective glass is longer than films, it also needs to be changed sometimes. The glass is on a silicone substrate, so it adheres firmly to the display. It takes some skill to remove it.
Before removing the protective element, you need to carefully prepare and purchase some tools and materials, namely:
- Spatula (or thin plastic card), mediator.
- Silicone suction cup.
- Lint-free napkin.
- Glass cleaner containing alcohol.
- Gloves.
Sometimes it happens that all the tools and materials listed above come with a new protective glass. But this happens quite rarely.
And the glass removal algorithm itself includes the following steps:
1 Wash your hands well with soap and water before starting work, and then dry them. You can not do this, but just wear gloves. This is to prevent fingerprints or streaks from appearing on the display. 2 If the glass is damaged, you need to choose the area that is best preserved, and on which there are no chips. In this place you need to attach the suction cup, pressing it firmly. 3 In the corner to which the suction cup is attached, you need to attach a mediator or a spatula, and pry it off. The edge of the coating should peel off. To do this, you will need to pull the suction cup towards you a little, but not much. To keep the screen from breaking. So we will achieve the goal so that a small distance forms between the screen and the glass. But if you do not have a suction cup, just insert the pick deeper. 4 In the course of glass peeling, deepen the tool. And if the display is large, you can use 2 mediators or spatulas for the procedure, moving them in different directions. 5 And the last step - we pull the suction cup towards us so that the glass completely moves away from the screen. In this case, you can grab its edges with your fingers and do the same.
How to stick glass on iPhone 6 and other devices
For everything to go perfectly, you need to stick the glass in a clean room where there is no dust. Before sticking the glass, you need to take a lint-free cloth or a simple cloth, wet the display a little with a cleaning agent or alcohol. This is necessary to clean the surface and remove fatty elements from it.
The gluing procedure is as follows:
1 A new protective coating for the display is taken in hand. As with removal, hands should be clean and dry. Or you need to wear gloves. 2 Remove the protective film covering the sticky surface. To do this, you need to pick it up by the tongue and pull. 3 And how to glue the element itself? The glass should be kept as close to the iPhone display as possible so that small particles of debris or dust do not get on it. After all, any surface tends to quickly accumulate dust. 4 Position the glass cover a few millimeters from the display, align and center it. When gluing, you need to act carefully and carefully make sure that all the holes for the keys, speaker and other elements match. 5 Further, the protective glass on the iPhone 5 falls closer to the screen. Lightly pressing and smoothing movements level the surface. So easily we were able to glue the glass to the display. 6 The surface is wiped with a dry cloth. 7 The glued element that protected the glass is removed from above.If at the end of the procedure you see small dust particles under the protective element, you can peel off part of the glass and blow it out with a vacuum cleaner or remove it with tweezers. Then you need to glue the element back again. How to re-glue glass, you already know.
Now you know how to stick a protective glass on an iPhone. There is nothing complicated in this procedure, replacing the glass on the iPhone 5S is as easy as shelling pears. Gluing the protective glass on the iPhone must be carefully prepared. And the main thing here is to keep everything clean.
Which is better - glass or film?
The answer is obvious - of course, it is better to opt for glass protection. But the point is not only in shock-resistant properties, but also in durability. One has only to note that the glass on an iPhone 4 or another version of the gadget costs twice as much as a regular film.
So the final choice is up to the user. Think for yourself - what is better - to pay more, but in the future to avoid expensive device repairs or save now, but then lay out a lot of money. Screen replacement is one of the most expensive types of Apple gadget repairs. But, on the other hand, the film is also not a bad option.
As a result, the summary will be as follows. The film is affordable. It protects the display from small scratches, removes glare and covers the entire screen. Do I need a protective film for the iPhone screen, given its characteristics? Certainly yes. Moreover, its cost is low, and how to stick a film is an even simpler task than in the case of glass.
Glass is an expensive option. It gives glare, but transmits light to the maximum, and also reliably protects against strong falls and deep cracks. And if you've found a way to save up for an iPhone, you won't be satisfied with the cheap security options. In any case, knowing how to save up for an expensive device, you can find funds for good accessories for the iPhone 6S or other device.
How to stick a protective glass on the iPhone yourselfMany iPhone owners try to treat the device as carefully as possible. For this, various covers, bumpers and protective glasses are bought.
How to do it
Before gluing the protective glass, remove the case from the iPhone. If the iPhone display is already covered with old film or glass, feel free to remove it. Wash your hands thoroughly to avoid getting dirt on the screen.
It is best to glue in a well-lit place to see every mote that hits the screen of the device. Well, choose the cleanest surface for glass stickers.
Getting Started
Step 1: Clean up the iPhone display.
To do this, use any microfiber cloth so as not to leave anything superfluous on the screen.
You can also use an alcohol wipe and then wipe the display with a microfiber cloth with a soft cloth.
Step 2. Additionally, we clean the smartphone screen using the supplied tape or any other sticker.
Just touch the display with tape and lift it back up. The sticky surface will collect any remaining dust.
Step 3. Now you need to remove the protective film from the adhesive side of the glass and attach it to the screen.
Important: hold the glass by the edges to avoid leaving unnecessary marks on it.
Step 4. Carefully place the glass on the iPhone screen.
If the glass is good, it will lie on the smartphone screen on its own. But for greater certainty, you can smooth it out yourself.
We run our finger through the center of the smartphone and begin to smooth until all bubbles are removed. If any small bubbles remain, take a plastic card and, using light pressure, slide it over the bubbles.
In this tutorial, we used Mocoll glasses. And it's not just that When you sadly look at the iPhone, the display of which is covered with a ruthless mesh, it's too late to think about protection. The manufacturer of protective accessories Mocoll took care of the consumer in advance.
All brand products are designed in such a way that the buyer spends a minimum of time gluing protective glass.
Considering that the Chinese brand Mocoll (our review) has been producing protective glasses for several years, the company's engineers have thousands of hours spent in research laboratories behind them.
Glasses are manufactured using high-tech equipment and receive a number of important properties during processing. Glasses from Mocoll:
They are only 0.33 mm thick. The glass is homogeneous and has equal thickness at any point. Among glass manufacturers, Mocoll has one of the lowest production tolerance percentages.
Mocoll glass easily withstands the impact of sharp objects and does not crumble into fragments upon impact.
Hardness at the level of 9H on the Mohs scale. Only diamond is higher.
The glasses have an oleophobic coating, so after sticking you will not feel any tactile changes from interacting with the iPhone screen.
Mocoll supplies its products with a rich package. The kit has everything to stick glass without additional purchases and searches for a piece of cloth or a plastic card to eliminate bubbles.
Mocoll has several options for safety glasses at once. 2.5D, 3D and advanced design - 3D glass with elastic edges to match the color of the device case.
As you can see above, installing Mocoll safety glasses is very easy. Due to the presence of a special silicone layer, you can not worry about the appearance of hated bubbles during gluing.
For every taste, color and wallet
Mocoll, in the truest sense of the word, has glasses of all shapes and sizes. The range includes glasses for tablets and smartphones (and not only Apple), there is also protection for the MacBook.
Among the most interesting options is special glass with protection against peeking.
It works in such a way that after gluing, you can only see what is happening on the iPhone display strictly at a certain angle. That is, you, as the owner, can easily chat or watch a movie, and the bus passenger sitting next to you will not see anything if you wish.
Glasses are arranged in such a way that they refract the light coming from the screen, making the picture inaccessible to others.
Mocoll glasses are very popular. Accessories of this manufacturer are used by many service centers and workshops. They are really very strong..wrapper ( padding: 10px;
#hid-button,.hid ( display: none; )
#hid-button:checked ~.hid ( display: block; )
#hid-button:checked ~ label ( background: #e4e4e1; )
#hid-button:checked ~ label:before ( content: "Hide"; )
label ( display: inline-block;
Ever since the days of plastic phones, resistive films have been a screen protector. They protected the display from scratches, but in the event of a fall, the sensor may be damaged. In addition, the film worsens the view, and on the touch screen it also slows down the movement of the finger. The development of technology has led to the emergence of an oleophobic coating, from which protective glasses are made. How effective are they really?
Tempered glass is a coating that has been chemically treated. It is several times superior to the film. The surface hardness is 2-3 times greater than that of the film. Its thickness is 0.26mm, 0.33mm, even 0.5mm. Such a layer is not visible to the eye, it is difficult to feel it with your fingers, but it does not interfere with using the device. Through the transparent protective glass on the phone, a clear image is transmitted. A finger glides easily on a smooth surface.
Glass has a five-layer structure:
- silicone base that fixes the glass on the display;
- a containment layer that holds back a broken screen;
- anti-reflective layer that prevents tarnishing in bright light;
- protective layer responsible for the absence of damage;
- Oleophobic coating protects the screen from grease, fingerprints and moisture.
The manufacturing process consists in heating the surface to a high temperature and etching in reagents. As a result, the structure of the glass changes, increases the mechanical strength and hardness. Despite all these advantages, protective glass has one serious drawback. The increase in stability reduces the ability to withstand blows to the butt. The screen can withstand being dropped flat on pavement, but may shatter if hit with an angle. Even in the event of such a blow, the touchscreen still remains intact.
Each new generation of flagships is equipped with oleophobic coating. However, the protective glass on the phone gives protection from scratches and scuffs. And even for that, it's worth using.
How to choose and stick a protective glass on the phone - tips
Before sticking a protective glass on the phone, you should choose the right glass based on the screen parameters. Let's consider them in more detail.
OGS displays with 2.5D touchscreen
OGS is a touch screen that is tightly glued with a transparent adhesive to the module. 2.5D is a type of touchscreen without the usual edges, that is, with polished chamfers. Such screens were used by Apple in the iPhone. Since the sensor smoothly passes into the frame, it is impossible to stick the glass. It will hang over the edges, forming an air gap, or leave the edges unprotected.
The behavior of glass on such an apparatus depends on its quality and impact characteristics. When falling from a great height with the sensor down, the low-quality glass will burst without affecting the touchscreen. But high-quality glass will remain intact, but the sensor may suffer. Adjacent close to the screen, the glass has a higher strength than the touchscreen. But high rigidity does not allow shock absorption.
OGS displays without 2.5D
Such sensors do not have polished edges. The glass will cover the edges of the sensor. In the event of a fall from a height or a side impact, the display is less likely to be damaged. Therefore, protective glass must be glued on such screens.
On such displays, the sensor and matrix are connected along the perimeter, and between the surface there is a layer of air of 0.1-1 mm. Upon impact, such a structure flexes faster. Therefore, a protective glass should be glued to the screen. If we take into account that such displays are installed on budget models, then a smooth surface will also increase the sliding of a finger on the screen.
Before sticking the protective glass on the phone, you should prepare a napkin, alcohol, medical gloves, silicone suction cup (if any).
Usually they come with glass. Otherwise, all parts will have to be purchased separately.
Sticking should be done in a well-lit room, since in case of dust particles it will not be possible to separate the screen. Therefore, you should learn in advance how to properly stick a protective glass on a smartphone:
- 1. Degrease the screen. Putting on gloves, wetting a napkin in alcohol, we wipe the screen from streaks.
- 2. The screen should be grasped by the edges with your fingers. The sticky layer must remain intact. Otherwise, the adhesion reliability will deteriorate. The ideal option is to grab the glass with a suction cup.
- 3. Remove the protective film from the bottom side. We hold the glass at a distance of 5-10 cm from the screen so that dust does not stick.
- 4. Slowly bring the glass to the screen. As soon as it began to seize, we draw a napkin in the middle (from the speaker to the buttons).
- 5. As soon as the center sticks, we blow out the air, drawing a napkin from the middle line to the edges.
- 6. When the glass is fully adhered, you can remove the top film.
From the first time, it will not work to stick the protective glass on the smartphone correctly. In case of dust ingress, you need to peel off the edge from the corner closest to the bubble with a bank card. A gap of a couple of millimeters is enough to pull out the dust with tweezers or blow it out.
How to stick a protective glass on an iPhone
You can properly glue the protective glass on an Apple smartphone in the same way as on any other phone. First, you should disinfect your hands so that there is no dust left on the film. Then you should attach the glass to the device, try on the borders. Then remove the glass and wipe the screen with a napkin and a damp cloth. We remove the protective film and lower the glass to the screen so that all the cutouts match exactly. Smooth the surface with a napkin from the center to the edges to remove bubbles and dust. The whole process takes 10 minutes.
However, not everyone succeeds in sticking the glass perfectly the first time. Usually there are air bubbles. To get rid of them, it is enough to attach a dry rag to the place and push the air out.
How to glue the original glass
Before sticking the protective glass on the phone, you need to remove the old one.
Due to the difference in weight, glass is harder to remove than film. It is tightly connected to the touchscreen, but not by glue, but by electrostatic properties. Do not dismantle the glass with sharp metal objects. They can damage the screen, the silicone suction cup can tear off the cables.
If dismantling is carried out due to improper installation, then the easiest way to remove the glass is by using a tab at the top of the glass. The old surface can be removed by prying off the edges with a credit card, and pulling the surface gently with your hands or a suction cup. Broken glass should be removed piece by piece, starting with the largest.
During installation, it is easier to hold the new glass using a silicone suction cup. If this is not at hand, then you can use ordinary tape. It is attached to the edges of the protective glass film.
Today, most safety glass comes with cut edges. Such 2.5D sensors are completely adjacent to the screen. But due to the smaller size, they do not cover the entire visible display area. During the installation process, it is easier to eliminate the shortcomings. It is enough to hook the edge of the glass with a bank card.
Original glasses are produced as close as possible to the size of the screen. They cover the entire display. But there are always unglued edges that are noticeable when the display is off.
Especially for the Apple iPhone, Full Cover glasses are made with painted frames around the display. The glass is glued to the screen, completely repeating the shape of the smartphone.
For popular positions on Android, Full Cover glass is also released. It is glued around the perimeter and held along the edge. This affects the responsiveness of the display, dust quickly gets under it.
Service life and operation
The lifespan of the protective glass depends on how you use your phone. If the device is constantly located together with sharp objects. for example, in a bag next to the keys, the screen is quickly scratched. This will not render it unusable, but the aesthetic appearance will be violated.
Small particles and metal dust can not only clog the ports on the case, but also get under the glass. Dust and dirt accumulates under the non-glued edges. These particles can scratch the display itself.
In general, if you store your smartphone in a closed case, the glass will last for several years, ensuring not only the safety of the gadget, but also its aesthetic appearance.
Video
How to stick glass on iPhone?
Additional protective glass for the phone is a modern alternative to the usual films for screens. This accessory will protect your smartphone from all types of mechanical damage to the display (scratches, abrasions, cracks from falling devices).
If you decide to purchase a protective glass for your iPhone, check out the basic tips for choosing this accessory:
- glass thickness determines the level of protection of the phone from drops and bumps;
- choose the type of glass - matte or glossy. The second option is cheaper. Glossy products protect the screen from bumps, but not from scratches;
- frosted glass fully protects your iPhone from bumps, scuffs, drops and glare.
Installing a protective accessory on the phone screen does not require special skills. Let's take a closer look at how to stick a protective glass on an iPhone in a few simple steps.
Step 1: Cleaning the Display
Tidy up your workspace. Make sure that there is no dust on the surface, which may eventually remain under the film. Then open the package and lay out all the elements on a clean, flat surface.
Clean your smartphone screen with a cloth and glass cleaner. Wipe the display surface thoroughly and wait until it is completely dry. This action will remove even invisible dust particles. Try not to touch the iPhone screen itself anymore, so as not to create new streaks and dust particles. Wipes for the initial cleaning of the phone come with a protective glass.
Step 2: Unpack the protective glass
At the next step, unpack the accessory and prepare it for sticking on the phone. Take the screen and peel off the protective layer, which, after sticking, will be in contact with the phone's display. After detaching the protective layer, try not to touch the protective glass, otherwise fingerprints will remain on the product.
Step 3 Sticking
Flip the protective glass down with the side that was freed from the film. Position the accessory above the smartphone screen without touching it. Try to match everything as evenly and accurately as possible to avoid uneven sticking.
The next step must be done very quickly. Gradually apply the glass to the iPhone display in the direction from the top of the case to the bottom. Release the film so that the side sections stick to the phone themselves. By cleaning the display well, bubbles will not form.
Step 4. Smoothing the surface
Users do not always know how to stick glass on an iPhone. As a result, the result may not be ideal. To remove small bumps or air trapped inside, take a piece of microfiber (included with the glass) or a clean cloth and gently wipe the phone, moving from the center of the display to the sides, applying light pressure. In this way, flaws can be eliminated.
A film is also glued to the outside of the protective glass. Remove it immediately after removing all the flaws. Now turn on the device and check the responsiveness of the sensor. Normally, the additional screen should not affect the smartphone in any way.
We eliminate errors
If too much dust and dirt gets under the protective glass during gluing, it will be inconvenient to use the smartphone. The sensor may react worse to touch, and the appearance of such a phone will not be the best. Many users are wondering how to re-glue glass on the iPhone and is it possible to do this at all? Yes, you can.
If the accessory does not stick properly the first time, carefully remove it from the display and set it aside on a clean surface. Thoroughly wipe the iPhone screen again and make sure it is free of dust and dirt. Only after cleaning the screen, paste the glass again. More accessory to unstick is not worth it.
How to remove glass from iPhone?
As a rule, users only need to remove the protective glass in one case - when it is broken during a fall or impact. It is very important to remove the accessory correctly so that the fragments do not damage the main display of the smartphone.
Take a plastic card and pry the edge of the protective glass with it. Then advance the card under the glass until it is completely removed. This method allows you to create a kind of barrier waiting for the display and a damaged protective accessory.
Let's do it this way - if a person does something for the first time, then he can be called a noob in this matter. I have never put a screen protector on my phone! I saw this process only once. Therefore, you can safely consider me a noob in gluing protective glass. In this article I will answer the question - can a noob stick a protective glass on an iPhone well?
So, the glasses were ordered back in October on Aliexpress. They did not track in any way after leaving China. Two months have passed, I was extended the term of protection at my request. As a result, I opened two disputes and the sellers returned the money to me. But the Russian Post was to blame (who would doubt it). A couple of days ago, they sent me two notifications, saying that your parcels need to be picked up urgently (they are almost 30 days in the mail). That is, stupidly the postman did not deliver notifications.
Started from the first glasses for iPhone 6 Plus. I ordered from this link.
The glass was in a foam box. To damage the glass inside, even the Russian Post would have to try very hard.
Before the first experience, I watched a video on Youtube about the correct gluing - I did not learn anything new. The essence of the process is to wipe the screen with an alcohol wipe and then carefully apply the glass to the screen.
In the box was not only the glass itself in a special case, but also a double set of small wipes: wet (alcohol) and dry. I wiped the screen with them in turn:
Then he took out the glass, peeled off the protective film by pulling on a special label. And carefully placed the glass. And then I was surprised - it lay down perfectly and the air itself came out within 5-7 seconds. No bubbles or other artifacts were found.
The process turned out to be extremely elementary.
Second glass for iPhone 5S I ordered from another seller. Here it is already in a small cardboard box. In addition to the same step-by-step wipes, the Dust-absorber was included in the kit. Why is it needed? I just did the same on the knurled as with the first glass.
Nuance. The glass for the iPhone 5S is slightly larger than the visible part of the screen, so no matter how you sculpt it (even if it’s not even), it will still fit nicely and cover the entire screen, but the iPhone 6 Plus turned out to be a tutelka in a tutelka in width. Therefore, I recommend increased accuracy so that the glass does not steal a couple of pixels.
Output: And here is the answer to the question in the title. Yes, anyone can stick a protective glass on their phone without difficulty and experience. If you are afraid to stick inaccurately, well, order two pieces. All the same, it will not disappear - there will be a spare.
