New models of smartphones for the modern user are not just a means of communication. Mobile devices that combine the functions of a telephone and a computer are a status item that emphasizes the image and impeccable reputation of their owner. But sometimes the overall style of the device deteriorates due to the appearance of cracks and scratches on the smartphone screen. Fortunately, this problem can be prevented by applying a screen protector to the display. But remember that if this procedure is performed carelessly, ugly air bubbles remain under the film. Sometimes a defect appears as a result of small dust grains settling on the inner side of the film. In this situation, it will not be possible to eliminate it by simply re-sticking the protective accessory. The film will have to be completely replaced.
1 Bubbles on the protective film of the phone: how to remove them?
Information on how to remove air bubbles from the surface of a protective film will be relevant and useful for owners of mobile gadgets who self-stick a useful accessory on the display
2 Replacing the film on the phone - the main nuances
Replacing the protective film on the smartphone display must be done as carefully as possible and in a clean room where there is no dust. The best option for replacing the film is the bathroom. The humidity level in it is high, so the dust does not float in the air, but settles down. Accordingly, it will not be able to get on the inner surface of the film that you attach to the display. The technique of gluing a protective accessory to a smartphone screen consists of the following steps.
3 Air gets under the protective glass - how to remove it?
Removing air bubbles from under the denser protective glass in a smartphone is a little more difficult than from under a thin film. But if you wish, anything is possible. To help you - advice from experienced owners of mobile devices who managed to independently solve the problem of air bubbles under protective glass.
- 1. If air has accumulated under the surface of the glass in the smartphone, try to "squeeze" it out of there by swiping a plastic card or a thick driver's license across the screen.
- 2. An ordinary needle will help you remove air bubbles under the protective glass. Gently thread it under those areas of the coating where there is accumulation of air. Lift the glass to release the air, and then press it back against the display surface so that no air masses get under it.
- 3. Fishing enthusiasts can try to remove air from under the protective glass using a fishing line. Carefully slide it under the protective accessory on the smartphone screen and slide it all the way until the air bubbles disappear. Then take out the fishing line, and put the glass back in place, gently pressing it.
- 4. A household hair dryer will help to correct the defect in the form of air bubbles on the smartphone screen. Experienced craftsmen claim that air bubbles will disappear if the protective glass coating is first heated with a stream of hot air from a hair dryer (removing the device 20-30 cm from the screen), and then putting the device under a press from books overnight (on a flat surface, display down) ... Usually in 12-14 hours all the air is released and the bubbles disappear.
Note! You can clean the inner surface of the protective film or glass from your smartphone using a strip of tape. Stick it on the surface of the accessory, and then remove. The adhesive element will remove dirt, small debris and dust from the film surface. After such cleaning, you can stick the protective cover back on.
Useful Tips for Sticking Film on Your Phone Screen at Home
If you want the display surface to remain clean and free of air bubbles after self-fixing the film, adhere to the following recommendations in the process.
- 1. It is better to change the film or protective glass in a well-ventilated room with a high level of humidity. This will prevent dust from entering the surface of the accessory.
- 2. When changing the protective glass - be extremely careful and do not press hard on it. Otherwise, you can break a fragile part.
- 3. If your hands are dirty, wash them first, and only then proceed to the procedure of gluing the film (protective glass). Otherwise, greasy, ugly marks will remain on the surface of the accessory.
- 4. If air bubbles have formed under the film, remove them with a medical syringe. Just pass its "nose" under the accessory and pump out the air. In essence, the syringe will act as a pump.
- 5. To remove excess dust from the film (glass), use a special tool Dust Remover.
So, now you know how to properly remove air bubbles from under the glass (film) on the smartphone display. If you adhere to the above recommendations, the film will be fixed on the screen evenly, without wrinkles or bubbles. The tips above will help you give your gadget a stylish and presentable look.
Some precautions when handling gadgets are by no means superfluous. Even novice users are well aware that the touch screen is one of the expensive items, the replacement of which costs a respectable amount. Significantly increases the strength indicators of the device by special glass that protects it with little mechanical stress. Many owners of mobile phones prefer to glue the protection on their own without contacting a service center. As a consequence, after such attempts, noticeable air bubbles appear, which spoil the appearance of the screen. Let's talk about how to get rid of such a nuisance, what exactly an ordinary user with no technical knowledge can do for this.
Methods for eliminating air under protective glass
Once again, we warn you that we will talk about ordinary procedures, there is nothing complicated about them. So, if the air gets caught, it is recommended to take one of the following actions:
1. In a number of simple cases, an ordinary piece of flat plastic can help. To solve the problem, a credit card or a driver's license is suitable, with which it is worth trying to drive out the bubbles that have appeared.
2. If you fail, do not despair. Obtain a small needle to gently pry on the edges of the guard. Use a needle in places where air contamination is noticeable. After the air is removed, firmly press the protective element against the screen of the gadget.
3. A standard hair dryer can help. It is necessary to warm up the smartphone a little for several minutes. In no case, do not bring the hair dryer too close! The equipment must work at a distance of 25-30 cm! After completing the activity, place the electronic product on a flat surface under a press of several heavy books. After about 6-8 hours, only a memory will remain from the air bubbles.
4. In the presence of a large number of blisters, it is worth resorting to a more radical method. It is quite possible that the air under the protective glass will disappear after the complete dismantling of the protection. After that, attach a strip of tape to the glass surface, onto which all small debris will go. Then put the glass accessory back in place.
Despite the apparent simplicity, each of the procedures described above requires careful preparation. Note that work should be carried out in an environment of maximum sterility, with a minimum of dust. At home, to solve this problem, it is advisable to use a bathroom - in rooms with a high level of humidity, there is much less dust. Do not exert significant physical effort with each action. The work is delicate, does not like haste, requires caution. Be sure to remove the grease from your hands, otherwise serious problems can arise.
Try to initially stick the glass correctly
To avoid problems, there is no need to remove the bubbles under the film on the phone, try to immediately stick the protective cover correctly. Understand that it is better to do a task well initially than to try to correct mistakes later. We will provide useful information that will help you avoid problems when installing a thin accessory.
Remember to remove grease stains from the screen surface. Be sure to use a liquid with a high alcohol content to achieve this. Do not forget to wear disposable medical gloves that do not restrict movement and allow you to perform precise work. Remember that the sticky side of the accessory must never be touched. In this case, the adhesive parameters of the coating deteriorate significantly. The ideal option among professionals is the presence of a suction cup, it significantly facilitates the process of completing the task.
If you have doubts about your own abilities, take your smartphone to a specialized service. Any master is able to solve such a simple problem for a modest reward. By the way, the quality of work largely depends on what kind of glass you purchased. Practice proves that failures occur much more often when trying to stick cheap copies. Therefore, never skimp on protection, buy only expensive copies.
Many people buy smartphones of new models not only to use all the modern functions of such gadgets, but also to emphasize their status. And what style can we talk about if the screen is scratched or cracked altogether. In order to prevent such possible troubles, almost every phone user uses a protective film for the display. Bubbles are caused by air trapped under the surface of a useful accessory such as a film. It so happens that a "defect" is formed due to a small speck of dust, then the process becomes a little more complicated - you will have to change the entire film. In order to stick the film on your smartphone for the first time or re-stick it, you need to know how to remove bubbles from the phone film, because this is perhaps the only and main nuance in this matter. Today we will tell you more about this and try to get around all the obstacles.
Replacing Film
This procedure requires extreme care and a high level of cleanliness in the room. It is best to carry out all manipulations in the bathroom, because due to humidity, dust does not fly in the air. The following is to be done:
- We take a smartphone in our hands and smooth out the air bubbles with our fingers or another flat, but not sharp object. If nothing comes out, then you will have to peel off the film and try to put it back in place again.
- It is best to wipe the display of a mobile device with a special computer wipe. With the same napkin, you can clean off all the dirt from the old film.
- Now we firmly take the device in our left hand, hold the edge of the film with our thumb and carefully glue it to the glass so that no air gets under it.
If you have been careful and your film is not too worn out, then everything should work out without difficulty.
Protective glass
How to remove air from under the protective glass? Here, everything is a little more complicated, since unnecessary movements can violate the integrity of the protective accessory. We recommend that you familiarize yourself with the most common tips from advanced mobile users:
- Use your driver's license or plastic card to squeeze the air out from under the glass surface.
- You can use the most ordinary needle that everyone has at home. Take a needle and thread it under those places where air has accumulated. Carry out the procedure very carefully - you need to raise the edge, and then press it tightly so that air cannot get there.
- If you have fishing tackle on hand, you can use a line. Pick up the accessories with the fishing line and guide it until the problem areas are over. All that remains is to put the glass back in place and press it gently.
- Some experts recommend using a household hair dryer to fix defects. Warm up the glass of your mobile device at a distance of 20-30 centimeters, place it with the screen facing down on a flat coffee table and leave it under a press from books overnight. During this time, all the air should go out.
Important! You can also remove the glass in any of the following ways and clean its surface with a strip of tape. The scotch tape will collect all dust and small debris, after which you can glue the protection back.
All the details we will tell you on another page of our site.
To avoid problems in the future, we have prepared a small list of recommendations for you:
- Do not apply the gluing procedure if your hands are dirty. Wash off sebum from your fingers, otherwise it can “leave marks” in your work.
- Both the protective glass and the film are best replaced in a damp, ventilated area. These precautions will help you avoid getting dust beneath the surface.
- Do not put too much effort when replacing the glass, otherwise you risk breaking it.
- You can use Dust Remover to remove excess dust.
- You can use the most common medical syringe to remove bubbles. Pass the "nose" and pump out the air from under the surface of the film or glass.
Video
Now you know how to remove bubbles from the phone film at home without the help of specialists who require a considerable amount of money for such a simple procedure. We hope our tips were useful to you, and now your modern gadget looks exactly as an expensive phone should look.
Having bought a new smartphone, we immediately think about how to save it so that it lasts as long as possible, because the purchase is not at all cheap and not everyone will allow themselves to buy a new gadget every day. In this article, I will tell you how to properly stick a protective film on your phone and tablet without bubbles and debris. Someone is given it easily, while someone learns this wisdom for a long time, although there is nothing special in it.
Before gluing the film to the screen, you need to prepare a little.
We need the following:
1. A wet wipe for the screens of phones, laptops, monitors, etc.
2. A clean dry cloth or soft eyeglass cloth.
3. Thin tape.
4. A credit card or similar piece of plastic.
And the desire to work a little and, of course, a good mood is also very useful!
Sticking a protective film on the screen
Step 1... We thoroughly clean the glass of the phone screen. To do this, we first use a damp cloth, then a dry one. Make sure that there are no dust particles, lint or hairs left on the screen. Otherwise, each of them will be a bubble under the film on the screen.
By the way, dry and wet wipes, as well as a plastic spatula, are often included with the films (especially with AliExpress). Personally, I don't really like using them, but in the absence of alternatives, they are also quite perfect.
After cleaning, turn the smartphone screen at an angle to the light and make sure that there are no dust particles or streaks on it.
Step 2... Each screen film has two layers to protect it from dust. Each layer has a tongue, which you can pull badly so that the layer begins to come off. They are labeled as Step 1 (first) and Step 2 (second). Tear off the first layer a few centimeters from the upper edge. In no case, do not open it completely right away, otherwise you will most likely not be able to properly and normally stick the film on the phone.
If the film lies flat, then tear off the protective layer further and glue it completely. It is electrostatically charged and will stick in a given direction.
Step 3... Using a credit card or a complete spatula, it is necessary to expel all bubbles by gradually moving them to the edges of the glass.
If everything was done correctly and you were lucky not to catch a speck of dust, then we tear off the second layer from the film by pulling on its tongue.
How to remove bubbles under the film on your phone
Now let's figure out what to do if the first time it was not possible to successfully glue the film to the phone screen and bubbles formed under it. If it's just air, then you should try to remove it with a card. But if it has accumulated next to a lint or speck of dust, then until you remove it, the bubble will continue to appear.
To remove it, we just need a narrow tape. We make two small strips. We glue one on a protective film to lift it. After that, remove the dust from the screen with the second strip of adhesive tape and return the film to its place.
How do I remove bubbles from the protective film on my tablet?
Removing bubbles that interfere with clearly seeing the image on the tablet can be done quite easily. Just peel off the film, wipe the screen with a special computer cleaning cloth, and stick the film back on.
It is very difficult to do this, it is easier to re-stick the film, after wiping the screen with a special napkin. to remove all microscopic dust particles. You can also try to pierce the resulting bubble with a needle and release the air from it. And it is always better to ask the seller to stick it carefully when buying a film.
It depends on how this bubble is formed ...
If it's just air that has gotten between the film and the glass, you just need to take a credit card (or something similar - for example, a student's ruler) and gently move this bubble to the nearest edge with the edge of the card.
If a bubble has arisen due to dust that has got under the film, practically nothing can be done ... You can only replace the lens itself, but this is a job that requires EXTREME neatness and high purity. At home, it is almost impossible to ensure the absence of dust in the air. You can try to go to the forest or to the seashore in calm and not very hot weather, preferably immediately after rain - in such conditions, the dust content in the air is minimal.
Basically, you can ignore the small bubbles between the protective film and the tablet screen. But if, nevertheless, the problem causes inconvenience, then you can take an ordinary sewing needle and very carefully pierce the film at the place where the bubble forms. Then you need to smooth this place with your palm. At the puncture site, air will escape and the problem will disappear. The main nuance of the operation is not to touch the screen surface with a needle.
These air bubbles can be easily removed by smoothing them out with a ruler. if they are large enough, then try to lift the film and kick out the bubble with your fingers, or with the same ruler, or gently pierce it with a needle.
Well, ideally, just delete this file and everything. But if all the same protection is necessary and there is no desire to remove it, then you can try one of the following two methods. The first is to make a puncture in the center of the air bubble with a thin needle and press it down with your finger - the air will come out through the puncture, the bubble will disappear. The second is to take a plastic spatula and gently drive the bubble to the edge of the film closest to it.
I usually just rub the eraser (eraser) from the air bubble to the edge of the film. If the bubbles are small, then they disperse easily.
In general, I noticed that now the screens of phones are made of very durable glass, it does not scratch, not only without a film, but also without a cover. I just have my smartphone in my bag, I have been wearing it like that for several months and there is not a single scratch on the glass.
There are several ways to remove bubbles from the tablet's protective film. The first thing to do is try to smooth out the bubbles that have arisen with your fingers. If it does not work, then you can peel off the film, and then carefully stick it back on. If this method did not work, then you need to take a needle or pin and carefully pierce these bubbles. And you can even peel off this film and throw it away so as not to steam.
How do I remove bubbles from the protective film on my tablet?
You can use your driver's license or plastic card to smooth out the surface of the protective film and expel any bubbles that appear on the screen. When the bubbles are pushed to the edge of the screen, they escape and leave a smooth surface on the screen of the portable device.
If the appearance of bubbles is caused by dust particles, then in this case there is a special tape called Dust Remover - with its help you can get rid of this problem. The principle of its operation is that a speck of dust sticks to the surface of this tape and remains on it (a speck of dust can also be removed from the tape), and then bubbles, if they remain, are removed in the above way.
Removing bubbles from the protective film can be very problematic. That is why you need to try to immediately stick the film without bubbles.
Before applying the film, you need to thoroughly wash your hands to remove sebum from your fingers.
Wipe the screen of the device (tablet, smartphone) on which you are going to stick the film with a napkin, the napkin is attached to the film. The task of the napkin is to remove not only dirt, but also dust particles and various villi invisible to the eye, since it is usually because of them that bubbles form.
I pasted the film gradually, gently holding one edge, and with the other hand pressed it with a cloth and gently led to the edge of the screen while gluing.
If, nevertheless, bubbles have formed, then it is better to gently lift off the part glued with the bubbles and stick it again. You can get rid of some of the bubbles if you start to adjust them with a cloth from the middle to the edge.
