About the firmware of DVB-T2 digital set-top boxes:
Update software(firmware) of your equipment is made only in cases where there are any problems, or the update will add useful functions device. It is not recommended to flash devices unnecessarily. in the process of updating the firmware, there is a possibility of equipment failure... If you are not sure that you can handle the firmware update yourself, we recommend that you contact the appropriate service center to qualified specialists in the PLUS-MINUS Company.
How to update the firmware:
Proceed as described in the user manual. If given information is not in the manual, then contact the service technical support Company "PLUS-MINUS" ..
Download ORIEL firmware file:
Receiver firmware file Oriel 710- download (version 1.3.5). This update is only suitable for receivers with serial numbers from 710121000001 to 710130211200.
... Receiver firmware file Oriel 720- download (version 1.3.5). This update applies only to receivers with serial numbers 720121000001 through 720130202200.
810
- download (version 3.4) This update is suitable only for receivers with serial numbers from 81111200001 to 81111205050 and from 81120100001 to 81120106060. Firmware instructions.
... Oriel Receiver Firmware File 820
- download (version 1.0 from 01.08.2012). This update applies only to receivers with serial numbers 82120100001 to 82120105280. Firmware instructions.
Oriel Receiver Firmware File 910
- download .
... Oriel Receiver Firmware File 920
- download .
Download firmware file SELENGA T2-1000:
05/07/2013. After switching from DVB-T to DVB-T2 format, the following channels are not scanned in this firmware:
MODEL: DZHDT
VERSION SW: 9610.9615.1121105R
HW: 1612301202112FD65
-----> software should be replaced with the following:
MODEL: T2600
VERSION SW: SW130108_v10.0
HW: 161230120650
(usb_upgrade_all_selenga_T2-1000_v10_T2600_130108.bin) - download
-----> or the software should be replaced with the following:
MODEL: T2600
VERSION SW: SOFTWARE: MNP AHTEHH_v11.0
HW: 161230120650
SELENGA T2-100 Receiver Firmware File
(usb_upgrade_all_selenga_T2-1000_v11_T2600_15062013.bin) - download
SELENGA T2-100 Receiver Firmware File
(usb_upgrade_all_selenga_T2-1000_v13_T2600_28062013.bin) - download
Download SELENGA T2 HD850 Firmware File:
SELENGA HD850 Receiver Firmware File
Download firmware file SELENGA T2 HD900, HD1000:
SELENGA HD900 / HD1000 Receiver Firmware File
(usb_upgrade_all_selenga_T2-HD900_HD1000_07062013.bin) - download
Download DIMBOX firmware file:
Receiver firmware file DIMBOX(usb_upgrade_all_dimbox040313.bin) - download
Download firmware file GS TE8714:
Receiver firmware file GS TE8714
(2012_11_07_TE8714x_for_0.0.660v.rar) - download
(2012_11_07_TE8714x_for_4.14.4xx.00.01v.rar) - download
(2012_11_07_TE8714x_for_4.15.125.00.01v.rar) - download
(Instructions for updating the GS TE8714 receiver) - download
ATTENTION! The archive for downloading must be selected depending on the current software version of your receiver. The current version can be viewed in the "Status" item of the main menu of the receiver.
Advantages new version software relative to the previous 0.0.660:
- Improved S / PDIF audio output
- Improved receiver stability in PVR and Timeshift modes
- Receiver software update procedure has been greatly simplified
- Improved work user interface receiver
Attention! After flashing a new version of the software, it is impossible to return to the previous one!
Download firmware file WORLD VISION:
Receiver firmware file World vision T23CI
(T23CI_V1.0.8_20130315.abs) - download
(T23CI_V1.0.9_20130805.abs) - download
(t23ci_v1.1.1_20131017.abs) - download
World Vision T23CI Update Instructions (WorldVision_T23CI_manual.pdf) - download
Receiver firmware file World Vision T40(usb_wv-20130807-upgrade_all_flash.bin) - download
Download firmware file 4HOME DVB-T2 1811:
Receiver firmware file 4HOME DVB-T2 1811 (updated_software_4homedvb-t21811.zip) -download
Download firmware file DCOLOR DC710HD T2:
Receiver firmware file DCOLOR DC710HD T2 (DCOLOR_DC710HD_DVB_T2_RUSSIAN_upgrade.zip) -download
Download GLOBO T2 firmware file:
Receiver firmware file GLOBO GL60 T2 (Software_DVB-T2_RU_FTA_1.0.0_GL60_2013-03-28.rar) -download
Receiver firmware fileGLOBO GL60 T2(Software_DVB-T2_RU_FTA_1.2.1_GL60_REV_300_2013-12-19_DOUBLE_LCN_SORT_FIX.rar) - download
Receiver firmware file GLOBO GL100 T2 (Software_DVB-T2_RU_FTA_1.1.5_GL100_2013-09-25.rar) -download
Receiver firmware fileGLOBO GL100 T2(Software_DVB-T2_RU_FTA_1.2.1_GL100_REV_300_2013-12-19_DOUBLE_LCN_SORT_FIX.rar) -
When the set-top box is turned on for the first time, a software update is performed. The software update process takes a few minutes. Do not unplug your device until the updates have been fully installed.
Further, the software update occurs automatically after STB reboot. To reboot, press the "RESET" button on the STB front panel or disconnect its power supply from the mains. If a new version of the software has been released, the process will begin automatic update ON.
The software update process is displayed on the TV screen and on the front panel of the set-top box:
ADB3800W software update
The process takes 5-7 minutes, while progress is displayed on the front panel of the set-top box and on the TV screen (in% from 0 to 100). Do not disconnect the set-top box from the network until the updates are fully installed and the image of the subscriber portal appears.
AmiNET130 software update
The process takes 6-8 minutes, during the first minute the indicator on the front panel of the set-top box will blink with variable frequency... The TV screen intermittently displays the Amino splash screen and a black screen. Do not disconnect the set-top box from the network until the updates are fully installed and the image of the subscriber portal appears.
Sagem IAD84HD / IAD85HD software update
When you turn on the set-top box for the first time, a message about the need to update the software will appear on the TV screen. To start the software update process, press the red button on the remote control with the inscription "A". The process takes 5-6 minutes, and an indicator showing the status of the update process will be visible on the TV screen. Do not disconnect the set-top box from the network until the software update is completely finished and the image of the subscriber portal appears.
Software UpdateDune HD TV-102
The basic software for this media player is installed by the company. It allows you to use 7Sky TV services and standard functions player. Attempt self installation new software from the Dune HD website will make it impossible to use 7Sky TV services.
After the release of a new version of the software for 7Sky TV, when the set-top box is turned on, a message will appear on the TV screen about the need to update the software. To start the software update process, press the red button on the remote control with the inscription "A". A message appears with current version Software and new; to start the process, press the "ENTER" button. The process takes 5-6 minutes, and the process of downloading and applying the update will be shown on the TV screen. Do not disconnect the set-top box from the network until the software update is completely finished and the image of the subscriber portal appears.
Today digital technologies they penetrated so deeply into the everyday sphere that life without them became simply unthinkable. New format broadcast - digital television, provides improved picture and sound quality, greater noise immunity. Modern set-top boxes allow not only passive viewing of HDTV channels, but also control this process. The user has access to the ability to “rewind” the broadcast, pause it, not to mention the banal recording of his favorite programs. But this real opportunities TV set-top boxes are not limited to, only to gain access to the full functionality of the device, you will need to update its software. Under flashing technical device means updating the software on it. The procedure is comparable to reinstalling Windows on the personal computer... Manipulations are carried out in order to expand the functionality, improve technical characteristics.
Re-flashing the Rostelecom set-top box: losses and acquisitions
Let's try to figure out what the firmware of the Rostelecom prefix gives and what risks exist when carrying out this procedure. Most popular model Operator's set-top boxes - IPTV RT-STB-HD Standart. Technically, it is a complete copy of the MAG-250, developed by the Ukrainian manufacturer Infomir with the functionality cut down by the Rostelecom firmware. And in order to return the prefix to its original capabilities, it is necessary to reflash it into the original MAG-250.
The latest models of IPTV RT-STB-HD Standart are produced by Rostelecom with its own remote control, unsuitable for controlling the MAG-250, due to the absence of some of the functional buttons on it.
V in this case you will have to use not only the standard firmware from Infomir, but also the modified one. There is a nuance - from experience it is easier to put it first standard firmware, and only then, if necessary, fill it with a modified one.
First about the losses: with firmware iptv set-top boxes Rostelecom will become unavailable interactive services operator, since access to them is provided by the original software. This is where the cons, perhaps, end.
From acquisitions: home media center with WI-FI support and DLNA, as well as the ability to watch TV channels from the playlist without the operator's tariff restrictions.
Digital Living Network Alliance (DLNA) is a standard that allows various multimedia devices to be combined into a single user network.
Rostelecom set-top box firmware: preparatory procedures
If you have read this section, the question is: "Is it possible to reflash the Rostelecom prefix?" in front of you is not worth it. The procedure is quite simple and usually succeeds. It remains only to figure out what is needed for this.
So, to flash a Rostelecom set-top box, you will need:
- hardware: PC with a cable for connecting a set-top box;
- software: mcast.exe, any dhcp server (one of the most convenient and popular is dualserver), directly current version official firmware, if necessary - a modified version.
All downloaded software must be put into one folder created in the root of the C drive. For convenience of further explanations, let's call the folder infomir.
On this preliminary stage The flashing of the iptv-set-top box by Rostelecom is over. Now on to the fun part.
How to flash a Rostelecom prefix: step by step instructions
If you have finished all the preparations, and you feel the strength to start, let's proceed. We will analyze step by step how to reflash the Rostelecom prefix.
First, you need to reset the prefix to the initial, default settings of the manufacturer. The firmware of the Rostelecom TV set-top box may end successfully without this procedure, but it is better not to risk it.
Keep in mind that the Default button on the back panel of the STB, seemingly intended for this purpose, does not work. Therefore, you need to reset the settings through the menu - item Def. Settings. After the message “Set default settings !!! Press OK ”press OK and exit the menu with saving changes - item“ Exit & Save ”.
Further, the flashing process is performed on the computer. In the main menu, select the Run item and in the Open line and type ncpa.cpl, and then click OK. In the list network connections select the required one, call for it context menu and go to Properties. At the bottom of the tab there is a list of the components used by this connection. Open in it "Internet Protocol version 4 (TCP / IPv4) and double click go to the properties of the protocol. Enter the values of the IP address - 192.168.1.1 and the subnet mask - 255.255.255.0.
Then the DHCP Server service starts. Win + R → cmd → C: \ infomir \ dualserver –v (full path to the program).
Launching mcast.exe, click on "Connect by local network"(IP 192.168.1.1) and click Select on the right side of the window. In the program window, you need to enter the values of the IP addresses of the processes: 224.50.0.70:9000 for stream # 1, 224.50.0.51:9001 - for stream # 2. Press the start button for both streams. The set-top box is connected to the PC and in its main menu, select the Upgrade Tools → MC Upgrade command. As a result of these actions, the firmware will be loaded and saved in the STB's memory. Reboot the device and - voila - the new media center is ready to go.
Rostelecom has severely curtailed the Mag-250's capabilities to the point of offensive. And using it without reflashing is like driving a Ferrari on Russian off-road, strictly observing the speed limit. You can, of course, but is it worth it?
