How to set up Apple Watch: charge, turn on, pair with iPhone, and install apps. Apple Watch won't turn on

(3 estimates, average: 4,67 out of 5)

Apple Watch Series 3 Is the latest generation of smartwatches from the Cupertino tech giant. Unlike Series 2, they are equipped with an autonomous LTE module that works through a built-in eSIM (not yet supported in Russia), so they can be used even without a smartphone. But it will still be required to activate the device.

How to turn on Apple Watch Series 2, 3?

To turn it on, press and hold the "long" (not round!) Side button until the manufacturer's logo appears on the display.

If after 10-15 seconds of holding the long side button, the screen does not flash and the device does not turn on, make sure that it is sufficiently charged. Connect the "charger" and leave for 30 minutes. After that, you can try to turn on the device again.

How to set up Apple Watch Series 2, 3?

For the initial setup, you will also need a smartphone updated to the latest iOS version, with Bluetooth enabled and an active Internet connection (via a mobile network or Wi-Fi).

How to do the initial setup

In order to initially set up your smartwatch, you need an iPhone with internet access. How to pair these two devices:

• Include them;
• Bring your watch to your iPhone. Wait for a while until a message appears on the phone screen prompting you to use your smartphone to make settings. In it, click "Next". If it doesn't appear, check Bluetooth - it should be turned on. You can also open the corresponding application and click the Create Pair button;
• After that, a special animation will appear on the watch screen, and the smartphone will turn on the camera through which it will recognize it. Position the display of the companion device in the center of the viewfinder as shown in the prompts. If automatic recognition does not occur, click the Create Manual Pairing button. The wizard will show you instructions for pairing devices;
• Choose which hand you plan to wear the watch on;
• Agree to all terms of use;
• Enter your Apple ID password.

How to connect Apple Watch 2, 3 to WiFi?

The smartwatch, upon initial activation, copies the settings profile from the connected smartphone. That is, if Wi-Fi, GPS, Siri, etc. are enabled on the iPhone, they are automatically activated on the companion device as well. Wireless passwords will also be transmitted along with the rest of the data.

You can enable WiFi on Apple Watch 3, as well as disable it or configure other settings, directly in the corresponding window of the First Time Setup Wizard.

What else can you do?

In the Quick Start Wizard, you can also:

• Set a password for login. It will be activated when you remove this accessory from your hand;
• Set up a branded payment service;
• Install applications from the AppStore.

During the initial setup, various tips for use will be shown on the smartphone screen.

Key features of Apple Watch Series 2, 3

Analysis of Apple Watch Series 2, 3 activity

The program for tracking physical indicators is called "Activity" and is preinstalled with watchOS, that is, it is ready to work immediately after the initial setup.

Interesting

Instructions on how to turn activity tracking on or off are shown directly in the first-time setup wizard on your smartphone. There are hints in the application itself.

The donut chart interface displays the following metrics:

• The number of calories burned while moving (the "Mobility" parameter);
• Total duration of movements (parameter "Exercises");
• The number of hours in the current day, in each of which you moved for at least 1 minute (parameter "With warm-up").

To view detailed information about each parameter, you need to swipe up on the screen with pie charts.

The Exercise and Warm Up options are not configurable. "Mobility" can be changed by a strong tap on any screen - after that a screen will open with the settings for the number of calories that need to be burned to reach the daily goal.

Reminders about the need to "walk" are configured in the control application on the smartphone, in the tab "My Watch" - "Activity".

How to measure pressure on Apple Watch Series 2, 3?

No way. This model, like the previous ones, is not equipped with a built-in tonometer and therefore cannot measure blood pressure.

Heart rate measurement on Apple Watch 2, 3

To measure your heart rate, you must start the Pulse program from the applications menu. In addition, the device constantly analyzes the heart rate when the "Training" mode is active, as well as 3 minutes after its completion.

When you open the Pulse program for the first time, the application will offer you to turn on notifications about increased heart rate if you are not physically active. This function can be activated if required.

Heart rate variability Apple Watch

To measure heart rate, photoplethysmography technology is used, i.e. the pulse is analyzed by the degree of light transmission of blood in the vessels under the skin.

As a result, the quality of heart rate measurement can vary depending on how the photocells are adhered to the skin, on the skin color, on the user's health and other factors. The exact value may differ by several beats per minute from the measured value, both upward and downward.

Sleep analysis in Apple Watch Series 2, 3

There are no built-in tools for monitoring the quality and phases of sleep in this companion device. Therefore, for tracking, it is recommended to use third-party software that can be downloaded from the AppStore - such as Sleep ++, AutoSleep, Sleep Better, Sleep Tracker, etc.

How to track sleep on Apple Watch 2, 3 using third-party software

The principle of operation of various third-party software is approximately the same. Would need:

1. Install the desired sleep tracker from the AppStore;
2. Open sleep tracker and start tracking mode.

Smart alarm for Apple Watch Series 2, 3

To use the watch as a smart alarm, you will also need to install third-party software that supports this function. For example, Sleep ++ or similar from the above list.

How do I use Apple Pay on Apple Watch 2, 3?

In order for the branded payment service to work, you will need to set a password code. This is described in the instructions for the initial setup of the device. In addition, right in the same menu, you can link the card with which you plan to pay for purchases.

To configure the service, if this item was skipped in the initial configuration menu, you will need:

1. Open the Watch application on your smartphone;
2. Open the "My Watch" tab;
3. Open the item "Wallet and Apple Pay";
4. If a passcode has not been set on the watch, the application will prompt you to install it right now. Do it;
5. Click "Add card";
6. Select a card from the list of already linked ones - or enter the data for a new one;
7. Enter the security code of the card;
8. Click "Next" and wait for information from the issuing bank;
9. Click Next.

That's it, the branded payment service will work.

To pay in a store, you need to quickly press the side button on the watch twice and then bring it with the screen down to the terminal. They vibrate slightly when activated.

Need to know

If the size of the transaction exceeds 1000 rubles, you will have to enter the PIN-code of the linked card on the terminal to pay.

Unlock Mac with Apple Watch

The watch can only unlock Mac computers and laptops that run macOS High Sierra and support a Bluetooth wireless connection. In addition, all company devices must be associated with the same account. To set up unlocking, you need to do the following:

1. On a computer or laptop, open the "Settings" application, select "Protection and Security", then "General";
2. Check the box next to "Unblock Mac with Watch";
3. Enter your account password;
4. Confirm.

Everything. The computer will now unlock automatically.

How do I charge Apple Watch Series 2, 3?

To charge, you need to use the included wireless charger. It is enough to connect it to the network and put the watch back side on its active surface. The charger is equipped with special magnets that automatically align it.

AirPower wireless charging can also be used.

How to charge Apple Watch outside the home

For charging, you can use not only the household network. The power cable can also connect to the USB ports of a computer, laptop, external battery (powerbank), or any similar charger.

How to update Apple Watch 2, 3?

The software update (watchOS) is performed via a tethered iPhone smartphone. Instructions:

1. Set your watch to charge. Until the update is completed, you cannot remove from the charge;
2. Make sure they are more than 50% charged;
3. Open the Watch application on your smartphone, in it - the "My Watch" tab;
4. Select the item "Basic", in it - "Software update";
5. Download the update. If necessary, you will need to enter a password for your account;
6. The update will install automatically;
7. Installing the update may take time. Wait for completion. The corresponding indicator will inform about it.

You can remove the watch from charging only after the update is completed.

Can Apple Watch be connected to Android?

No. Apple Watch does not work with Android phones. There is no third-party app that mimics the corresponding iOS software.

However, the user community is looking for a different way to pair these two devices. But at the moment, the answer to the question "Does Apple Watch work with Android" is no, it doesn't.

Apple Watch Series 2, 3 Quick Guide

How to check Apple Watch 2, 3 for authenticity

First, make sure it's a Watch, not an iWatch smartwatch or something like that.

How to check Apple Watch upon purchase:

1. Conduct a visual inspection. Make sure that the case is free of any connectors, including slots for SIM cards or memory cards, connectors for charging, etc .;
2. Turn on the device. Make sure it turns on in principle;
3. Try to connect to your smartphone. If, during the initial setup, the device prompted you to enter your account data, you can enter. The main thing is that there is no "Activate Watch" screen.

How to turn off GPS on Apple Watch 3

GPS does not turn off. You can turn it off on the phone, then the number of geolocation requests will decrease slightly.

Apple Watch Series 2, 3 won't charge - what to do?

If Apple Watch won't charge, you can try the following:

1. Make sure the power supply is plugged into a power outlet and that there is power. Try a different outlet;
2. Make sure the wireless charger is in contact with the watch and the magnets are aligned. Try reconnecting. Try flipping the charger;
3. Make sure that the chargers (including the wireless module, cable and power supply) are original and supplied;
4. The charger must not have a shipping tape on either side;
5. The charger and watch must be clean;
6. Try to force restart your watch. Press the round and side buttons and hold them for 10 seconds. After rebooting, put on charge again;
7. Try a different cable, a different power supply, or a different wireless charger.

If they still do not charge, take them to a service center.

How to reset Apple Watch to factory settings

The easiest way to reset is to remotely delete all personal data via the iCloud service:

1. Open the icloud.com website on your computer;
2. Log in with your account;
3. Select "Find iPhone";
4. Choose your watch from the available devices;
5. Click "Erase" and then select "Next" until the process is complete;
6. Also, click the "Delete" button (the icon with a cross) next to the name of the clock.

Through the app it is a little trickier. More on this will be written later in this manual in Russian (in the section "How to break a pair").

In order to reset the watch (to carry out the so-called "Apple Watch Restore"), the associated iPhone must be connected to the Internet via a mobile connection or Wi-Fi.

How to charge Apple Watch without original charging

The third generation companion device (Apple Watch series 3) has limited support for Qi wireless charging and may be compatible with some chargers. Try placing it back against a Qi-enabled active charger for a few seconds. If charging goes, this device can be used.

How to unpair Apple Watch 2, 3

Before selling the watch, you will need to remove your own credentials from the watch. How to unlink Apple Watch from Apple ID:

1. Open the control application on the phone;
2. Open the "My Watch" tab;
3. Open the "Information" menu (denoted by the i symbol in a circle next to the watch name);
4. Select "Break pair";
5. If a tariff plan is used, click "Delete tariff";
6. Enter the password for your account;
7. Reaffirm your desire to break the pair.

Unlinking also resets to factory settings.

I do not receive notifications on Apple Watch Series 2, 3

This may be due to the following:

• The smartphone to which the smartwatch is connected is currently in use. Then notifications are displayed on it;
• The watch has a screen lock or Do Not Disturb mode. Unlock or disable this mode through the Control Center;
• The watch is disconnected from the phone. This is reported in the Control Center with a special pictogram. Turn on Wi-Fi and Bluetooth on your phone, and on your watch, first turn on Airplane Mode and then turn it off.

How to unlock Apple Watch 2, 3

To unlock the watch, touch its screen or briefly press any button, and then enter the previously set passcode.

How to change the band on Apple Watch 2, 3

The watch uses special straps with proprietary fastening. It will not work to apply the standard spring-loaded, common in analog devices. But to change the strap, it is enough to remove the old one and install a new one in its place until a characteristic click appears.

How to remove the strap from Apple Watch

1. Turn the watch face down;
2. Press the strap lock button (located next to the strap);
3. While holding the release button, slide the strap to the side.

How to turn off Apple Watch

To turn off the watch, press and hold the side button until the Off slider appears, and then slide it.

Have a brand new Apple Watch? Congratulations! Sit back and put everything aside. You will have to: pair with your iPhone, update watchOS, customize the Apple Watch for yourself, and, of course, install some cool apps. I'll tell you about all this now.

My bad first setup experience

Setting up the Apple Watch for the first time wasn't quite as quick as I expected it to be. The process itself is very easy, but the speed of rebooting, charging and synchronizing takes some time. Therefore, having bought a new watch, do not think that you will set it up in 5 minutes in the nearest cafe over a cup of coffee and go with it for a walk around the city. In any case, I didn't succeed.

I bought an Apple Watch at the airport when it was more than two hours before boarding. And I spent all that time charging, setting up and updating watchOS.

The stumbling block was the charging itself. The clock was discharged into the trash and did not even want to turn on. I partially charged them from the "power bank". Doing it on the go is a challenge. Magnetic charging does not hold up well and constantly falls off the watch.

After charging the watch to about 20 percent, I began the process of setting up a pair of Apple Watch with an iPhone, but at the end of the synchronization of applications, the clock was again discharged and the whole process had to start from the very beginning. Including the charging itself.

The second time everything worked out, but the update to the latest watchOS version took some more time. As a result, after almost 2 hours, I received a ready-to-use Apple Watch with almost empty batteries, so I spent the next 2 hours of flight again fully charging them.

But in reality, it’s not so bad. You can connect Apple Watch to iPhone much faster if you don't make my mistakes. It took me 15 minutes to re-pair the Apple Watch with the iPhone. But by this time, you need to add charging, time to install applications and watchOS updates. Anyway, I recommend brewing coffee. Let's go!

How to connect Apple Watch to iPhone

You need a charged Apple Watch, a phone with Bluetooth running, and the Watch app. Pairing devices is very intuitive: the watch and the phone tell you what to do and where to press. To connect Apple Watch to iPhone, you need to do the following:

1. Charge Apple Watch at least 60%... Synchronization with an iPhone, setting quickly "eat up" the battery. And possible updates to watchOS requires the watch to be charged at least 50%. This is a very important point that will save you a lot of nerves. It takes approximately 55-60 minutes to charge Apple Watch from 0% to 60%;

1. Turn on Apple Watch holding the side button for a long time (if they do not turn on, then, most likely, they are very discharged and you need to charge the Apple Watch again). The watch will immediately ask you to select the interface language and go into pairing mode with the iPhone.

1. Launch the Watch app on iPhone and click on the “Pair with Apple Watch” button and point the video finder of the iPhone camera at the “galaxy” on the watch screen. The process is similar to scanning a regular QR code. Everyone, your watch is familiar with the iPhone. But this is where the fun just begins.

Follow the prompts on the iPhone to complete the pairing process. You will be asked to perform a series of actions that many are already familiar with when activating an iPhone or iPad.

Setting and hand selection... If this is your first watch, then tap Set As New Apple Watch. If you have configured it before, you can click Restore from Backup and follow the instructions on the screen. Then press Left or Right on iPhone to select a hand.

1. Enter your Apple ID password to enjoy features such as Digital Touch and Handoff. If Find My iPhone isn't turned on on your iPhone, you'll also be asked to turn it on.

1. P check the settings... IPhone settings from the Diagnostics & Usage, Location Services, and Siri screens will be transferred to Apple Watch, and vice versa. Therefore, if the settings for these services are changed on one device, they will be updated on the second.

1. Create a password... If you click Create Passcode or Add Long Passcode on iPhone, you can create a personal passcode using your Apple Watch. Then you need to decide whether the iPhone will automatically unlock the watch.

1. Synchronize programs... Click Install All to sync iPhone apps that are compatible with Apple Watch. Tap Later to sync only basic information such as Mail, Contacts, and Messages.

The duration of this process depends on the amount of data being synchronized. Keep the devices close to each other until you hear a beep and feel the slight pulsation of the Apple Watch.

The clock turned on. What's next?

Next, Apple Watch needs to be customized for yourself. And I will tell you how to do this using my personal example. In fact, my changes affect almost all settings, so by setting up the watch according to my instructions, you will immediately become familiar with all the settings of the Apple Watch.

We will do all the watch settings through the Watch app for iPhone. Something can be configured directly through the watch, but working with a small screen is not as convenient as with phones. So open the Watch app again and let's start.

How to update Apple Watch

First, you should check if there are fresh firmware for the Apple Watch and update to the latest one. For this:

1. Open the app Watch
2. Select "Basic"
3. Click "Software Update"

If there is an update for the watch, the iPhone will inform you about it. To install it, just follow the instructions on the screen and the iPhone will do everything by itself. But remember that the watch and phone must be charged at least 50% to install.

How to install apps on Apple Watch

If you skipped the automatic installation of all programs compatible with Apple Watch during the watch settings, you will have to install them manually.

All compatible programs are available in the "My Watch" tab and are conditionally divided into two categories: software from Apple and everything else. To install the app on Apple Watch:

1. Open the app Watch;
2. Choose any application from the list (below);
3. Click Show on Apple Watch.

That's all. After a couple of seconds, the program will be installed on Apple Watch and will appear in the list of applications.

In some applications, you will see additional options like "Show in Preview" and so on. We will return to these parameters a little later.

How to automatically install apps on Apple Watch

If a new application appears on the iPhone, which has a version for the Apple Watch, then it can be automatically installed on the watch. For this:

1. Open the app Watch;
2. Go to the "My Watch" tab;
3. Select "Basic";
4. Select "Install programs";
5. Turn on "Automatic installation of programs".

How to sort apps on Apple Watch

A list of all applications on the Apple Watch can be seen by clicking once on the Digital Crown. In the center there is always a circle of clock icons, and icons of other applications appear around them.

In order not to look for the desired program for a long time, I place the most necessary ones around the clock icon, that is, in the very center. For this:

1. Open the app Watch
2. Go to the "My Watch" tab
3. Select "Appearance"
4. Arrange the icons in the desired order

How to set up notifications on Apple Watch

When the necessary programs are installed, I proceed to setting up notifications. By default, they are completely duplicated from your iPhone. But I prefer to keep only the really important ones. Not only is this less distracting but also saves your watch battery.

1. Open the app Watch
2. Go to the "My Watch" tab
3. Select "Notifications"

Scroll to the bottom and turn off those notifications you don't want to see on Apple Watch. I have a couple of dozen of them.

How to change the brightness of the Apple Watch screen

In Apple Watch, there is no manual brightness control in the usual sense, it always changes automatically depending on ambient light. But you can choose from three automatic brightness algorithms. This can be done both on the watch itself and in the Watch app on the iPhone.

1. Open the app Watch
2. Go to the "Text brightness and size" tab
3. Set the options you want

Personally, I set it to a minimum and do not experience any inconvenience, even at the equator. The display is a little faded in the sun, but the information is still visible.

What Apple Watch Shows When Activated

Apple Watch automatically activates when you raise your hand to look at your watch. The watch face is displayed by default. But I love to see the last running app displayed. For this:

1. Open the app Watch
2. Go to the "My Watch" tab
3. Select "Basic"
4. Select "Activate Screen" (bottom)
5. Select the desired action

By the way, when you are on the watch face screen, a double tap on the Digital Crown will open the last launched application.

How to change the face of your Apple Watch

Unlike all the previous paragraphs, setting up the Apple Watch dial takes place on the watch itself. To change the watch face on your Apple Watch, press down firmly on the screen until you feel a vibration (Forth Touch press, like iPhone 6s). A menu with a selection of possible dials will open in front of you. Choose the one you like and click "Configure".

Left-right swipes will move you between watch face settings, and can be adjusted by turning the Digital Crown.

most watch faces have room to display extensions from third-party apps. These settings are found on the last screen and can also be changed with the Digital Crown. Press the Digital Crown and then tap the dial to save your changes.

In conclusion

Voi everything you need to start your Apple Watch for the first time. Now you can start exploring the programs yourself. Many of my favorite iPhone apps already have versions for the Apple Watch, so you have a lot to play with.

On the case of a smart watch from Apple, there are only 2 buttons. However, many users who recently bought a gadget may not always understand how to turn on Apple Watch and how to configure them. Difficulties also arise when trying to synchronize a smart watch with a smartphone. The manufacturer offers tips specifically for Apple Watch users that can help if a similar problem occurs.

for the first time

On the right side panel of the smart watch there is a Digital Crown, under which the button is located. The key is responsible for a wide range of functions. In this regard, it is not very different from the "Power" button on the iPhone. The element is responsible for turning the device on and off.

To activate Apple Watch, you should hold down the button on the side panel of the device and hold it in this position for several seconds until the Apple logo appears on the display of the gadget. The device turns off in the same way.

After holding the button for 2 seconds, a special menu will appear on the screen, in which you can turn off, lock or put the device in the energy saving mode.

Apple watch not included? For such cases they have a hard reboot function. To perform this function, you must simultaneously press the wheel and the button, and then hold them in this position for several seconds.

Setting up Apple Watch

Apple Watch instruction indicates that you must have an iPhone 5s or later with the latest operating system to use the watch. The following operations should be performed directly on the smartphone:

1. You need to make sure that the Bluetooth wireless transmission function is turned on on your smartphone.
2. The iPhone must have access to the internet or mobile network.

After turning on the watch, you need to position it close to your iPhone. After some time, an inscription will appear on the smartphone screen, signaling that the device is ready for configuration.

To start managing, you must click "Continue". The message may not appear right away. In this case, you should open the program for operating the watch (the rules of use describe in detail how to download and install it) and select the "Create a pair" item in it. To perform an action, you need to place the devices at a short distance.

A special animation will appear on the watch screen.

Official user guide indicates that it is necessary to position the gadget's dial with animation in the field of view of the iPhone's viewfinder. Then it is required that the pairing message appears on the smartphone.

If for some reason you cannot use the camera, you can manually pair with the smartwatch. To do this, select the advanced menu item and follow the instructions that appear on the screen.

Detailed instruction in Russian language prompts you to choose which hand the owner prefers to wear the device. Provides the ability to manually adjust the clock or restore settings from a backup. If in case prolonged non-use some of the settings have lost their relevance, you can always reset the parameters.

The program on the smartphone will offer to accept the changes, in order to save them, you must agree to the terms of the application.

Smart watches are activated using Apple ID. After the corresponding field appears, you must enter the password from the service into it. If the password request does not appear, then you can sign in later. To do this, in the Apple application in the settings menu, select the "Apple ID" item, and then log in to the system. On smartwatches of the third series, some functions work only after you sign in to iCloud.

Some devices may not have the iPhone search service configured. In this case, an activation lock request will appear on the screen. This function prohibits the use of the device in case of loss or theft. If a lock warning appears on the watch screen, then the device is already linked to a different identifier. To unblock, you must enter the password and email address for the previously used ID.

IPhone sync

To set up your smart watch, you need to connect your smartphone to it. The process of syncing and connecting to Apple Watch depends on the amount of data available on your smartphone. It can last from a few seconds to several minutes. Completion of synchronization will be indicated by a beep and a slight pulsation of the clock. To confirm the completion of the process, press the wheel on the device.

If your Apple Watch won't turn on and won't respond to button presses, try solving the problem yourself. With the instructions and the tools you need, you can quickly fix simple faults. You can find out why the device does not turn on, check the integrity of the control board and the reliability of the contacts, even without special skills.

Most of the time, Apple Watch fails for the following reasons:

• the power button is broken
• moisture has entered the protective case
• clock stuck after an update or as a result of a software crash
• due to mechanical damage, the watch display was damaged

A common reason Apple Watch won't turn on is when the battery is drained or damaged. In this case, it is necessary to recharge or replace the battery. Hold the button on the side of the device and the Digital Crown to restart the watch until the Apple icon, Apple's signature icon, lights up.

Why does the device not start

If your Apple Watch suddenly stops turning on, the problem might be due to a setting issue. Pay close attention to the notifications that appear on the screen of Apple technology. In them, the developers describe the problems and give options for their elimination. If your Apple Watch is running low, connect it to the charger and wait for the company logo to appear.

If your Apple Watch stops turning on or responding to the charging connection, you can remedy the situation in the following ways:

• check the depth of insertion of the cable into the socket and the adapter into the socket
• remove the protective film from the charger
• clean the device from dirt and dust
• restart the device (press the side button)

How to quickly reboot an electronic device

You can also check that the charging is working properly. If the Watch icon is on, Apple should be charging automatically. Press the button on the side of the watch and press the Digital Crown to restart your Apple device and make sure your installed apps are working properly.

A common reason Apple Watch won't turn on is when Power Saver is running. In this case, pressing the screen will not start the clock.

What you need to know before proceeding with device recovery

To turn on your Apple Watch, press the power button, located on the right side of your device. In doing so, you will notice that the "apple" is on fire. The download duration is determined by the Apple device model and is usually about a minute.

The iWatch device belongs to the category of mini-computers, the installed applications on which must be periodically updated. Apple Watch users find their devices run faster after a software update. If you want to put Apple Watch into battery saving mode, hold the button on the right side of the device until the Eco Mode slider appears.

No messages on the display

Apple Watch is unable to function after being discharged. The clock display on which notifications appear is consuming a significant amount of power. A common reason why no alerts appear on a device is when the watch is locked or when Do Not Disturb is activated. You can solve the problem in the following ways:

• remove the passcode that prevents Apple Watch from turning on and the watch display is locked
• make sure that the settings for Apple technology are correct

Easy ways to fix devices

If you want to check if the charger is working properly, try restarting your watch. To do this, hold down the Side Button and Digital Crown for 10 seconds. In the event that the charge icon is not visible, leave the Apple device plugged in to a rechargeable appliance for several hours.

Simple ways to repair smartwatches that turn off spontaneously:

• drying devices
• charge replacement
• configuring the parameters of Apple technology

Difficult troubleshooting options

If your Apple Watch stops turning on and can't diagnose the problem right away, the damage could be serious. The malfunction may be associated with the failure of the button responsible for turning on the device, the malfunction of the microcircuit, or other reasons.

To determine the cause of the malfunction, you will need special equipment and tools. With their help, you can perform the following repair operations:

• remove and replace the button responsible for turning on the Apple device
• update the software if the clock freezes or turns off spontaneously
• Repair Apple Watch Power Chip
• replace the charger connector

Apple Watch users often experience such problems - after discharging, the watch freezes or turns off. To force a restart, press the side button and the Digital Crown at the same time. If after rebooting the watch turns on, but you do not see that the "apple" is on, or a notification with a red exclamation mark appears, this means that the device cannot be used due to a breakdown of the microcircuit or other parts.

An effective method for solving device problems

If your Apple Watch won't turn on and you need professional help, contact YouDo. Experts will quickly and inexpensively find out the reason why the device does not turn on, the clock is frozen, or the power button has stopped functioning.

Collaboration with Yudu performers provides the following benefits:

• provision of services with departure at any specified address
• replacement of parts with original components
• round the clock
• experience in servicing all models of iWatch devices

Leave a request on this page, describing your problem (for example, "the Watch logo is on, Apple is not charging"). Experienced performers can help you inexpensively any day of the week if your Apple Watch won't turn on at all.

(or pair with another iPhone), then you will certainly face the need to untie the device from the iPhone (unpair). It is very simple to do this: you just need to perform a number of simple actions, and you can do this even in the absence of a smartphone.

In contact with

You may also need to unlink Apple Watch from iPhone if one of the gadgets malfunctions.

How to untie (unpair) Apple Watch from iPhone if both devices are in front of you - method 1

1 ... Place both gadgets next to each other;

2 ... Open the Apple Watch application on the smartphone;

3 ... In the window that opens, at the bottom, there will be a menu “ My watch"- click on it;

4 ... After that, you should click on the item " Apple Watch", On the next screen you must click on "I".

5 ... By clicking on the " Unpair Apple Watch», You must confirm the cancellation of device synchronization, after which all data about the clock will be deleted from the communicator.

How to untie (unpair) Apple Watch without iPhone - method 2

It is possible to untie the watch from the smartphone, even if both devices are not close to each other (for example, if the iPhone is lost). To do this, go to the application " Settings"On Apple Watch (gear icon), go from there to the section" The main", Select the menu" Reset"And click on the item" Erase all content».

This action will reset your Apple Watch to factory settings (all data will be deleted) and will also unpair the existing iPhone pair.

How to untie (unpair) Apple Watch from iPhone, if the watch has a passcode, but you forgot it

There is a method to unlink the Apple Watch from the iPhone, even if a passcode was set on the watch, which you, by an absurd accident, forgot. For this:

1 ... Set Apple Watch to charge.

2 ... Press and hold the side button until the slider appears Off.

3 ... Press hard on the slider Off and swipe up, then a button will appear on the watch screen. Erase content and settings.

4 ... Click on the button Erase content and settings and confirm the action. The watch will be reset to factory settings (all data will be deleted), in addition, the Apple Watch will be unlinked from the iPhone.