How to get rid of bubbles under protective glass. How to remove bubbles from under the protective glass

Some precautions when handling gadgets are by no means superfluous. Even novice users are well aware that the touch screen is one of the expensive items, the replacement of which costs a respectable amount. Significantly increases the strength indicators of the device by special glass that protects it with little mechanical stress. Many owners of mobile phones prefer to glue the protection on their own without contacting a service center. As a consequence, after such attempts, noticeable air bubbles appear, which spoil the appearance of the screen. Let's talk about how to get rid of such a nuisance, what exactly an ordinary user with no technical knowledge can do for this.

Methods for eliminating air under protective glass

Once again, we warn you that we will talk about ordinary procedures, there is nothing complicated about them. So, if the air gets caught, it is recommended to take one of the following actions:
1. In a number of simple cases, an ordinary piece of flat plastic can help. To solve the problem, a credit card or a driver's license is suitable, with which it is worth trying to drive out the bubbles that have appeared.
2. If you fail, do not despair. Obtain a small needle to gently pry on the edges of the guard. Use a needle in places where air contamination is noticeable. After the air is removed, firmly press the protective element against the screen of the gadget.
3. A standard hair dryer can help. It is necessary to warm up the smartphone a little for several minutes. In no case, do not bring the hair dryer too close! The equipment must work at a distance of 25-30 cm! After completing the activity, place the electronic product on a flat surface under a press of several heavy books. After about 6-8 hours, only a memory will remain from the air bubbles.
4. In the presence of a large number of blisters, it is worth resorting to a more radical method. It is quite possible that the air under the protective glass will disappear after the complete dismantling of the protection. After that, attach a strip of tape to the glass surface, onto which all small debris will go. Then put the glass accessory back in place.

Despite the apparent simplicity, each of the procedures described above requires careful preparation. Note that work should be carried out in an environment of maximum sterility, with a minimum of dust. At home, to solve this problem, it is advisable to use a bathroom - in rooms with a high level of humidity, there is much less dust. Do not exert significant physical effort with each action. The work is delicate, does not like haste, requires caution. Be sure to remove the grease from your hands, otherwise serious problems can arise.

Try to initially stick the glass correctly

To avoid problems, there is no need to remove the bubbles under the film on the phone, try to immediately stick the protective cover correctly. Understand that it is better to do a task well initially than to try to correct mistakes later. We will provide useful information that will help you avoid problems when installing a thin accessory.
Remember to remove grease stains from the screen surface. Be sure to use a liquid with a high alcohol content to achieve this. Do not forget to wear disposable medical gloves that do not restrict movement and allow you to perform precise work. Remember that the sticky side of the accessory must never be touched. In this case, the adhesive parameters of the coating deteriorate significantly. The ideal option among professionals is the presence of a suction cup, it significantly facilitates the process of completing the task.
If you have doubts about your own abilities, take your smartphone to a specialized service. Any master is able to solve such a simple problem for a modest reward. By the way, the quality of work largely depends on what kind of glass you purchased. Practice proves that failures occur much more often when trying to stick cheap copies. Therefore, never skimp on protection, buy only expensive copies.

Today we will tell you whether a smartphone really needs a protective glass and whether it is capable of protecting a gadget in case of a fall. We will also show you which glass to choose and how difficult it is to install it.

The need for glass

When buying a smartphone, sellers often offer to glue a protective glass as an add-on, assuring that without it, well, it is absolutely impossible. If the display breaks - they continue - it will be easier to buy a new phone, plus scratches.

They are right that the price tag for replacing the display can go up to 60% of the cost of the device. But otherwise there are nuances. If the device is budgetary and it does not have the so-called protective tempered glass, then yes, it is better to stick the protection on it, otherwise scratches cannot be avoided, and even if the glass falls down, it absorbs a little.

But devices of the middle price category with a screen made using Gorilla Glass or Asahi technology do not need a piece of plastic 0.33 or even 0.22 mm thick, scratches are not terrible for such a device. Gorilla Glass displays are virtually scratch-resistant.

Impact on sensor performance

A persistent myth - glasses impair the performance of the sensor. In fact, this is not the case. The only thing is that there may be no oleophobic coating on the protective glass, and there will be just a bunch of prints on the display, and your finger will slide worse than on a “bare” screen. The sensor of a smartphone may not respond well if the glass is not glued well.

Glass or film

Glasses are a relatively recent phenomenon. At first, they were popular on the devices of the iPhone and Sony companies, but later the trend spread to all other models.

Of course, it's better to stick the glass on. Firstly, it is much easier to glue it than film, especially on a new machine. Secondly, it provides, albeit small, but still additional protection.

But there is an important clarification here. If you have a 2.5D display with rounded edges, regular screen protector won't stick around the edges or cover the entire screen. Therefore, it is necessary to clarify whether the glass will accurately cover the entire screen.

Real value

Glass prices sometimes go up to 2,000 rubles, which is not very cheap. Is the high price justified?

Not really. There are really expensive glasses from manufacturers such as Samsung, LG, etc. They are produced for curved displays, there are also glasses with colored frames to match the color of the device. Their price tag can go up to 1000 rubles. The purchase price of simple transparent glasses from little-known manufacturers is 50-150 rubles per piece.

Which glass to choose

There is a huge number of glasses from different manufacturers on the market, which one to choose?

Curved screen

If you have a smartphone with a curved screen, then it is advisable to buy a special glass with 2.5D or 3D effect for it. Otherwise, it will not adhere to the edges or cover the entire screen. Moreover, the inscription “2.5D” on the glass packaging does not mean anything. It is better to ask the seller if it is exactly full screen or not.

Color frame

It is best to avoid glass with colored frames. If transparent glasses are glued over the entire surface, then in colored glasses there is only at the edges. Also, they very often have a "gasoline stain" on the screen, which cannot be gotten rid of. .

Oleophobic coating

The good oleophobic coating prevents finger oil from sticking to the screen. The screen on such devices is always blank. For protective glass, such a coating may be worse than that of a smartphone, or it may be completely absent. Therefore, before buying glass, it is better to move it over it and see if prints remain and how easily your finger slides.

Matte or glossy

This is of course a matter of taste. In our opinion, glossy glass is better. Although it glares in the sun, but with it you do not need to turn the brightness to maximum to see the image.

Thickness

In fact, it doesn't really matter how thick the protective glass is - 0.22 or 0.33 millimeters, you won't notice the difference.

Installation

Many people think that there is some kind of special glue for installation or that it requires special equipment. In fact, there is nothing difficult in gluing, and on the glass packaging, as a rule, there are instructions with pictures.

1) First you need to degrease the surface of the screen and remove all debris from it. To do this, the manufacturer puts alcohol and dry napkins together with glasses.

2) After cleaning the screen, apply the glass, after removing it from it protective layer. There is a special sticker on the glass for this.

3) We carefully apply the glass to the screen so that it does not go over the edges. That, in fact, is all. The glass is glued.

If it didn't work out the first time, it's okay! You can pick up the glass with something, such as a toothpick, and try to re-glue it. If debris has managed to get under the screen, then the glass can also be lifted and the debris can be removed using the adhesive side of the tape.

About protective glasses for smartphone screens and their advantages over protective films. There were quite a few comments, someone said that it was pointless to glue something on the phone at all. If you think so, then this post is not for you. But among those who gave advice on how best to glue, no one told the method that I will describe below. Stumbled upon him relatively recently. And maybe I will act as the "captain of the Obvious", but, I hope, I will be useful to someone.

So, the usual way is to create a humid atmosphere to nail down all the dust (for example, go to the bath and turn on the hot shower), ideally clean the glass of the phone and quickly attach the glass before new dust has accumulated. Alas, sticking more or less smoothly does not work the first time. It happened that the glass had to be peeled off and glued again. This increased the chances of catching dust particles, and the sticky layer could be damaged. In any case, the plus of glass is that it hides almost any hairs, dust particles and even air bubbles disappear on their own in a day or two. Especially confused people can remove particles accidentally caught under the glass with scotch tape. However, as it turned out, there is a simpler way to "stick".

Most often, the glass comes with accessories - wet and dry wipes for cleaning the screen and a set of stickers. Well, big - for specks of dust, ok, but for what small (Guide Sticker) - I did not understand, and did not even think about it.

And the chest just opened. First, there is no need to remove the film from the protective glass. Place it ideally on your smartphone screen and secure with these narrowest stickers. Then "turn over" the glass and clean the smartphone screen well (you can still do this in a damp room). Remove the film from the glass and attach to the screen. Ready. Since I discovered this method, I glue everything the first time and almost perfectly!

Ask why I change protective glasses so often? It's simple - I ordered several 0.2 and 0.26 mm glasses for testing and it turned out that they were terribly fragile. Cracked even if you unsuccessfully put the phone on the table with the display down or hit something in the bag. So I spent them and ordered the usual 0.3 mm again and I'm glad. Yes, they are thicker and it is not so convenient to perform gestures from the edge of the screen (if your smartphone screen is rounded like the iPhone), but I sometimes drop my phone and I don't want to accidentally break the screen.

In the first one, I also wrote about glasses of the 3D type, which are also rounded to the edges, but in the end I turned out to be from their use. The version with the metal edging does not look very good, dirt gets under the edges. Carbon fiber looks great, but too fragile. Plus, some of the cases that "fit" over the edges of the iPhone are incompatible with 3D glasses. And I have a lot of covers and I change them periodically.

The problem is often related to flaking around the edges of the display. The upper left corner is most affected by this nuisance. Although the right one quite often does not stand aside. The situation is not the most pleasant, but it is quite possible to fix it yourself.

Restoration of the sticky layer of the protective film on the phone

There are several options for fixing the problem. Each user makes the choice in favor of a specific one independently, based on personal capabilities and preferences.

Some precautions when handling gadgets are by no means superfluous. Even novice users are well aware that the touch screen is one of the expensive items, the replacement of which costs a respectable amount. Significantly increases the strength indicators of the device by special glass that protects it with little mechanical stress. Many owners of mobile phones prefer to glue the protection on their own without contacting a service center. As a consequence, after such attempts, noticeable air bubbles appear, which spoil the appearance of the screen. Let's talk about how to get rid of such a nuisance, what exactly an ordinary user with no technical knowledge can do for this.

Despite the apparent simplicity, each of the procedures described above requires careful preparation. Note that work should be carried out in an environment of maximum sterility, with a minimum of dust.

Can the protective glass be re-glued to the smartphone?

At home, to solve this problem, it is advisable to use a bathroom - in rooms with a high level of humidity, there is much less dust. Do not exert significant physical effort with each action. The work is delicate, does not like haste, requires caution. Be sure to remove the grease from your hands, otherwise serious problems can arise.

Protective glass comes off at the edges
Why does the protective glass come off
What to do if the protective glass comes off

Tempered glass is designed to additionally protect the display and prevent it from being destroyed by impact or falling. And the accessory provides the required result without any particular difficulties. But only if it is properly glued to the base.
If glued incorrectly, the glass may partially peel off. Dust and dirt begin to accumulate under it, and the smartphone itself sharply loses its original aesthetics. And its security raises very serious doubts.
How to solve the problem? What should be done in such a situation and what may be required for this? Let's consider the issue in more detail, and also study those aspects that need increased attention.

In the first case, you will need to purchase a special tool in advance.

Why is my phone's protective glass peeling off?

We are talking about Border Liquid gel, which is offered by a Chinese manufacturer. It has a transparent base and ensures a good connection between the edge of the glass and the surface of the screen. It is enough just to apply the gel to the edge and press it firmly against the base. The procedure is not particularly complicated, and its implementation will not take much time.
But if the corner is unstuck, then you can do with improvised means. In this case, you will need a napkin, glycerin (vegetable oil) and a thin brush. Carefully apply the compound to the edge, completely filling all existing voids. It is better to remove excess product with a napkin. The thinner the initially exfoliated area was, the higher the quality of the work performed.

Why does the protective glass come off

The reason for peeling off can be different. Moreover, often there is not one provoking factor, but several at once. It all depends on the accuracy of a particular user, the conditions for using a smartphone and a person's frugality.

The most common problem is the following:

• The presence of chips and defects on the glass itself;
• Insufficient cleanliness of the working surfaces before gluing;
• Sharp temperature fluctuations when using the Iphone;
• Moisture or air gets under the glass;
• Clogging of the base from the inside by foreign particles.

Although situations with incorrectly performed gluing are quite common. Here we are already talking about the lack of proper experience and ignoring the basic rules of gluing.

What to do if the protective glass comes off

If the protective glass comes off, then this may be for 2 reasons:

• Preparation and gluing were carried out with violations;
• The glass itself is not compatible with a specific smartphone model.

In the first case, you can try to re-stick it. And here you should exactly adhere to the advice and recommendations offered by experts.

The work itself is carried out as follows:

• The display is wiped with a special rag for complete cleaning of all extraneous traces;
• The smallest dust particles are blown off by the air stream;
• The screen itself is degreased with a special liquid for the most durable connection with the installed coating;
• The location of the glass on the display is determined and the film applied to one of its sides is removed;
• The glass is laid on the surface of the screen and gently pressed against the base;
• The air remaining from the bottom is squeezed out to the edges to ultimately obtain the highest quality protection without the least visual defects.

This completes the work. If the glass does not fit initially, then it is more advisable to immediately replace it with a more suitable option. It can be universal or designed exactly for a specific phone.

The video was recorded for those who really need it and may come in handy. This advice is not for "professionals" who tear off the glass with their nails. Personally, I do not use protective glasses, but change the touchscreen on my phones, because.

The protective glass on the phone is peeling off

the touch response is better than the safety glass. 2 more tips: 1) The adhesive tape must be glued flush with the side edges of the protective glass, so that when peeling off the table, the glass does not break due to being held from the sides with adhesive tape. 2) It is best to glue the glass or protective film with a fan, then dust in the gluing area, definitely will not be (well, this is my opinion). The main thing is that you will be able to remove them several times without damage. Good luck to everyone!

Cat Love: Thank you, it helped, only my hands were crooked and bubbles. But thanks really works, I thought that the scotch tape would not help, but helped. OVERALL THANKS

Alexander Batkov: Can you please tell me I peeled off the glass, it was all cracked and there was like a type of glue, since the glue deteriorated, can I stick it without glue? Thanks in advance!

Ateev Alexander: Not idial but will fall

Ateev Alexander: I also tried it the first time it worked

Makar Trukhanov: best ！！

Ruslan Gutsol: THANKS))) HELPED VERY MUCH)))))) THANKS THANKS THANKS)

JOHN 1000: Specifically, the new protective 3D glass was fucked up when I tried to clean it. The new one was dusty. I thought I bought everything in vain. And my surprise when the scotch tape cleaned it off awesome. I thought the glue on the inside of the glass would get worse, but no, everything keeps super. Thank you Video author !!! Really works as it should !!! Good to all! 🙂

Denis K:A speck of dust will find its place under the glass

Ilya Budagovsky: Yes, the dark fucker set the screen for 2,500, and they saw the marriage when he already pasted the protection

Bakdaulet Kambar: Scotch tape helped a lot. At first, I was a fool using a rag and could not clean it in different ways, but did not think about scotch tape in any way. Thanks!

Koteika: And glue in the bathroom

Koteika: Advice on scotch tape. At first, try to simply glue different types on the glass and see if there are traces or not. Take the thinnest line.

Alexey Kalinichenko: Thank you, everything is fine))))))

Siniy Bocman: nishtryak, helped from the 5th time (re-glued the film) respect!

yulia yula: Probably this tape also heals cancer ...

Pavel Sachok: Useful information

VitoKarlioni: kakoi skochi nuzen

Gleb Sunyaikin: The video is very boring, but useful, but often mantle, otherwise you can fall asleep!

Maxim Mikhailov: it is necessary to fill the glass with polyurethane foam so that there are no dust particles

Roman Kostin: There was a similar problem on a smartphone, when it was installed in a bumper or cover, the book peeled off the protective glass or film (their thickness does not matter). the form of a barrel with a diameter of 14 mm used for chamfering in holes and on small parts) On the bumper along the perimeter, even in the video, you can see a small chamfer which, when bent at the corners, stands out most of all, having processed the nozzle at first the corners from which mainly delamination was going on, I decided The entire perimeter chamfer has stopped. The smartphone is held firmly. Try it. Good luck.

Video on this topic

Some precautions when handling gadgets are by no means superfluous. Even novice users are well aware that the touch screen is one of the expensive items, the replacement of which costs a respectable amount. Significantly increases the strength indicators of the device by special glass that protects it with little mechanical stress.

Many owners of mobile phones prefer to glue the protection on their own without contacting a service center. As a consequence, after such attempts, noticeable air bubbles appear, which spoil the appearance of the screen. Let's talk about how to get rid of such a nuisance, what exactly an ordinary user with no technical knowledge can do for this.

Methods for eliminating air under protective glass

Once again, we warn you that we will talk about ordinary procedures, there is nothing complicated about them. So, if air gets under the protective glass, it is recommended to take one of the following actions:
1. In a number of simple cases, an ordinary piece of flat plastic can help. To solve the problem, a credit card or a driver's license is suitable, with which it is worth trying to drive out the bubbles that have appeared.
2. If you fail, do not despair. Obtain a small needle to gently pry on the edges of the guard. Use a needle in places where air contamination is noticeable. After the air is removed, firmly press the protective element against the screen of the gadget.
3. A standard hair dryer can help. It is necessary to warm up the smartphone a little for several minutes. In no case, do not bring the hair dryer too close! The equipment must work at a distance of 25-30 cm! After completing the activity, place the electronic product on a flat surface under a press of several heavy books. After about 6-8 hours, only a memory will remain from the air bubbles.
4. In the presence of a large number of blisters, it is worth resorting to a more radical method. It is quite possible that the air under the protective glass will disappear after the complete dismantling of the protection. After that, attach a strip of tape to the glass surface, onto which all small debris will go. Then put the glass accessory back in place.

Despite the apparent simplicity, each of the procedures described above requires careful preparation. Note that work should be carried out in an environment of maximum sterility, with a minimum of dust. At home, to solve this problem, it is advisable to use a bathroom - in rooms with a high level of humidity, there is much less dust. Do not exert significant physical effort with each action. The work is delicate, does not like haste, requires caution. Be sure to remove the grease from your hands, otherwise serious problems can arise.

Try to initially stick the glass correctly

To avoid problems, there is no need to remove the bubbles under the film on the phone, try to immediately stick the protective cover correctly. Understand that it is better to do a task well initially than to try to correct mistakes later. We will provide useful information that will help you avoid problems when installing a thin accessory.
Remember to remove grease stains from the screen surface. Be sure to use a liquid with a high alcohol content to achieve this. Do not forget to wear disposable medical gloves that do not restrict movement and allow you to perform precise work. Remember that the sticky side of the accessory must never be touched. In this case, the adhesive parameters of the coating deteriorate significantly. The ideal option among professionals is the presence of a suction cup, it significantly facilitates the process of completing the task.
If you have doubts about your own abilities, take your smartphone to a specialized service. Any master is able to solve such a simple problem for a modest reward. By the way, the quality of work largely depends on what kind of glass you purchased. Practice proves that failures occur much more often when trying to stick cheap copies. Therefore, never skimp on protection, buy only expensive copies.

Protective glass comes off at the edges
Why does the protective glass come off
What to do if the protective glass comes off

Tempered glass is designed to additionally protect the display and prevent it from being destroyed by impact or falling. And the accessory provides the required result without any particular difficulties. But only if it is properly glued to the base.
If glued incorrectly, the glass may partially peel off. Dust and dirt begin to accumulate under it, and the smartphone itself sharply loses its original aesthetics. And its security raises very serious doubts.
How to solve the problem? What should be done in such a situation and what may be required for this? Let's consider the issue in more detail, and also study those aspects that need increased attention.

Protective glass comes off at the edges

The problem is often related to flaking around the edges of the display. The upper left corner is most affected by this nuisance. Although the right one quite often does not stand aside. The situation is not the most pleasant, but it is quite possible to fix it yourself. There are several options for fixing the problem. Each user makes the choice in favor of a specific one independently, based on personal capabilities and preferences.
In the first case, you will need to purchase a special tool in advance. We are talking about Border Liquid gel, which is offered by a Chinese manufacturer. It has a transparent base and ensures a good connection between the edge of the glass and the surface of the screen. It is enough just to apply the gel to the edge and press it firmly against the base. The procedure is not particularly complicated, and its implementation will not take much time.
But if the corner is unstuck, then you can do with improvised means. In this case, you will need a napkin, glycerin (vegetable oil) and a thin brush. Carefully apply the compound to the edge, completely filling all existing voids. It is better to remove excess product with a napkin. The thinner the initially exfoliated area was, the higher the quality of the work performed.

Why does the protective glass come off

The reason for peeling off can be different.

Moreover, often there is not one provoking factor, but several at once. It all depends on the accuracy of a particular user, the conditions for using a smartphone and a person's frugality.

The most common problem is the following:

• The presence of chips and defects on the glass itself;
• Insufficient cleanliness of the working surfaces before gluing;
• Sharp temperature fluctuations when using the Iphone;
• Moisture or air gets under the glass;
• Clogging of the base from the inside by foreign particles.

Although situations with incorrectly performed gluing are quite common. Here we are already talking about the lack of proper experience and ignoring the basic rules of gluing.

What to do if the protective glass comes off

If the protective glass comes off, then this may be for 2 reasons:

• Preparation and gluing were carried out with violations;
• The glass itself is not compatible with a specific smartphone model.

In the first case, you can try to re-stick it. And here you should exactly adhere to the advice and recommendations offered by experts.

The work itself is carried out as follows:

• The display is wiped with a special rag for complete cleaning of all extraneous traces;
• The smallest dust particles are blown off by the air stream;
• The screen itself is degreased with a special liquid for the most durable connection with the installed coating;
• The location of the glass on the display is determined and the film applied to one of its sides is removed;
• The glass is laid on the surface of the screen and gently pressed against the base;
• The air remaining from the bottom is squeezed out to the edges to ultimately obtain the highest quality protection without the least visual defects.

This completes the work. If the glass does not fit initially, then it is more advisable to immediately replace it with a more suitable option. It can be universal or designed exactly for a specific phone.

Many people buy smartphones of new models not only to use all the modern functions of such gadgets, but also to emphasize their status. And what style can we talk about if the screen is scratched or cracked altogether. In order to prevent such possible troubles, almost every phone user uses a protective film for the display. Bubbles are caused by air trapped under the surface of a useful accessory such as a film. It so happens that a "defect" is formed due to a small speck of dust, then the process becomes a little more complicated - you will have to change the entire film. In order to re-stick the film on your smartphone for the first time or re-stick it, you need to know how to remove bubbles from the phone film, because this is perhaps the only and main nuance in this matter. Today we will tell you more about this and try to get around all the obstacles.

Replacing Film

This procedure requires extreme care and a high level of cleanliness in the room. It is best to carry out all manipulations in the bathroom, because due to humidity, dust does not fly in the air. The following is to be done:

1. We take a smartphone in our hands and smooth out the air bubbles with our fingers or another flat, but not sharp object. If nothing comes out, then you will have to peel off the film and try to put it back in place again.
2. It is best to wipe the display of a mobile device with a special computer wipe. With the same napkin, you can clean off all the dirt from the old film.
3. Now we firmly take the device in our left hand, hold the edge of the film with our thumb and carefully glue it to the glass so that no air gets under it.

If you have been careful and your film is not too worn out, then everything should work out without difficulty.

Safety glass

How to remove air from under the protective glass? Here, everything is a little more complicated, since unnecessary movements can violate the integrity of the protective accessory. We recommend that you familiarize yourself with the most common tips from advanced mobile users:

• Use your driver's license or plastic card to squeeze the air out from under the glass surface.
• You can use the most ordinary needle that everyone has at home. Take a needle and thread it under those places where air has accumulated. Carry out the procedure very carefully - you need to raise the edge, and then press it tightly so that air cannot get there.
• If you have fishing tackle on hand, you can use a line. Pick up the accessories with the fishing line and guide it until the problem areas are over. All that remains is to put the glass back in place and press it gently.
• Some experts recommend using a household hair dryer to fix defects. Warm up the glass of your mobile device at a distance of 20-30 centimeters, place it with the screen facing down on a flat coffee table and leave it under a press from books overnight. During this time, all the air should go out.

Important! You can also remove the glass in any of the following ways and clean its surface with a strip of tape. The scotch tape will collect all dust and small debris, after which you can glue the protection back.

All the details we will tell you on another page of our site.

To avoid problems in the future, we have prepared a small list of recommendations for you:

• Do not apply the gluing procedure if your hands are dirty. Wash off sebum from your fingers, otherwise it can “leave marks” in your work.
• Both the protective glass and the film are best replaced in a damp, ventilated area. These precautions will help you avoid getting dust beneath the surface.
• Do not put too much effort when replacing the glass, otherwise you risk breaking it.
• You can use Dust Remover to remove excess dust.
• You can use the most common medical syringe to remove bubbles. Pass the "nose" and pump out the air from under the surface of the film or glass.

Video

Now you know how to remove bubbles from the phone film at home without the help of specialists who require a considerable amount of money for such a simple procedure. We hope our tips were useful to you, and now your modern gadget looks exactly as an expensive phone should look.